1.
Remove the circlip (B) from driveshaft splines (A) of the transaxle side PTJ case.
Do not disassemble the BJ assembly.
Special grease must be applied to the driveshaft joint. Do not substitute with another type of grease.
The boot band should be replaced with a new one.
Remove the circlip (B) from driveshaft splines (A) of the transaxle side PTJ case.
Remove the both boot clamps from the transaxle side PTJ case.
Using a flat-tipped (-) screwdriver, remove the both clamps of the transaxle side.
Pull out the boot from the transaxle side joint(PTJ).
Remove the clip (C) from the PTJ case (B).
While dividing joint(PTJ) boot (A) of the transaxle side, wipe the grease in PTJ case (B) and collect them respectively.
Be careful not to damage the boot.
According to below the illustrated, put marks (D) on roller of trunion assembly (A), PTJ case (B) and spline part (C), for providing assembly.
Using a snap ring plier or flat-tipped (-) screwdriver, remove the circlip (A).
Remove the trunion assembly (B) from the driveshaft (A) using the special tool (09495-33000).
Clean the trunion assembly.
Remove the boot (A) of the transaxle side joint(PTJ).
For reusing the boot (A), wrap tape (B) around the driveshaft splines (C) to protect the boot (A).
Using a plier or flat-tipped (-) screwdriver, remove the both side of clamp (B) of the dynamic damper (A).
Fix the driveshaft (A) with a vice (B) as illustrated.
Apply soap powder on the shaft to prevent being damaged between the shaft spline and the dynamic damper when the dynamic damper is removed.
Saperate the dynamic damper (A) from the shaft (B) carefully.
Using a plier or flat-tipped (-) screwdriver, remove the clamp on the side of wheel.
Pull out the joint(BJ) on the side of wheel into the transaxle direction.
Be carefull not to damage the boot.
Do not disassemble the BJ assembly.
Special grease must be applied to the driveshaft joint. Do not substitute with another type of grease.
The boot band should be replaced with a new one.
Remove the circlip (B) from driveshaft splines (A) of the transaxle side SFJ case.
Remove the both boot clamps from the transaxle side SFJ case.
Using a flat-tipped (-) screwdriver, remove the both clamps of the transaxle side.
Pull out the boot from the transaxle side joint(SFJ).
Remove the clip (C) from the SFJ case (B).
While dividing joint(SFJ) boot (A) of the transaxle side, wipe the grease in PTJ case (B) and collect them respectively.
Be careful not to damage the boot.
According to below the illustrated, put marks (D) on roller of trunion assembly (A), SFJ case (B) and spline part (C), for providing assembly.
Using a snap ring plier or flat-tipped (-) screwdriver, remove the circlip (A).
Remove the trunion assembly (B) from the driveshaft (A) using the special tool (09495-33000).
Clean the trunion assembly.
Remove the boot (A) of the transaxle side joint(SFJ).
For reusing the boot (A), wrap tape (B) around the driveshaft splines (C) to protect the boot(A).
Using a plier or flat-tipped (-) screwdriver, remove the both side of clamp (B) of the dynamic damper (A).
Fix the driveshaft (A) with a vice (B) as illustrated.
Apply soap powder on the shaft to prevent being damaged between the shaft spline and the dynamic damper when the dynamic damper is removed.
Saperate the dynamic damper (A) from the shaft (B) carefully.
Using a plier or flat-tipped (-) screwdriver, remove the clamp on the side of wheel.
Pull out the joint(BJ) on the side of wheel into the transaxle direction.
Be carefull not to damage the boot.
