1.
Install the bushing (B) on the stabilizer bar (A).
note
Bring clamp (C) of stabilizer bar (A) into contact with bushing (B).
Install the bushing (B) on the stabilizer bar (A).
Bring clamp (C) of stabilizer bar (A) into contact with bushing (B).
Install the bracket (D) on the bushing (B).
Install the rear stabilizer bar to the rear cross member.
Install the rear stabilizer bar bracket (B) and link (A).
Tightening torque
Nut(C)
: 44.1 ~ 53.9N.m (4.5 ~ 5.5kgf.m, 32.5 ~ 39.8lb-ft)
Nut(D)
: 58.8 ~ 78.5N.m (6.0 ~ 8.0kgf.m, 43.4 ~ 57.9lb-ft)
Install the rear cross member.
Support the rear cross member assembly (A) with the jack.
Install the rear cross member mounting bolts (A), nuts (B) and plate (C).
Tightening torque
Bolts(A)
: 156.9 ~ 176.5N.m (16 ~ 18kgf.m, 115.7 ~ 130.2lb-ft)
Nuts(B)
: 156.9 ~ 176.5N.m (16 ~ 18kgf.m, 115.7 ~ 130.2lb-ft)
Install the rear cross member stay (A) and mounting bolt (B) and nut (C).
Tightening torque
Bolt(B)
: 68.6 ~ 88.3N.m (7 ~ 9kgf.m, 50.6 ~ 65.1lb-ft)
Nut(C)
: 68.6 ~ 88.3N.m (7 ~ 9kgf.m, 50.6 ~ 65.1lb-ft)
After matching a match mark (C) on the rubber coupling (A) and rear differential companion (B), Install the propeller shaft mounting bolts (D).
Tightening torque
: 49.0 ~ 68.6N.m (5 ~ 7kgf.m, 36.2 ~ 50.6lb-ft)
Install the wheel speed sensor (A) and the parking brake cable (B) to the rear axle carrier.
Tightening torque
Wheel speed sensor (A)
: 6.9 ~ 10.8N.m (0.7 ~ 1.1kgf.m, 5.1 ~ 8.0lb-ft)
Install the brake caliper (B), then tighten the brake caliper mounting bolts (A).
Tightening torque
: 63.7 ~ 73.5N.m (6.5 ~ 7.5kgf.m, 47.0 ~ 54.2lb-ft)
Support the rear lower arm with a jack as shown in the illustration.
Install the rear shock absorber (A).
Tightening torque
Bolt(B)
: 137.3 ~ 156.9N.m (14 ~ 16kgf.m, 101.3 ~ 115.7lb-ft)
Nut(C)
: 98.1 ~ 117.7N.m (10.0 ~ 12.0kgf.m, 72.3 ~ 86.8lb-ft)
After checking the distance(453±10mm(17.83±0.39in)) between the wheel housing garnish (A) and the hub assembly (B) as shown in the illustration, tighten the mounting bolts and nuts of rear chassis part with specified torque.
Install the wheel and tire (A) to the rear hub (B).
Tightening torque
: 88.3 ~ 107.9N.m (9 ~ 11kgf.m, 65.1 ~ 79.6lb-ft)
Be careful not to damage the hub bolts (C) when installing the rear wheel and tire (A).
