8495357

1.

Electrical systems consist of a lot of harness and connectors, poor connection of terminals can cause various problems and damage of component.

2.

Perform checking procedure as follows.

(1)

Check damage of harness and terminals : Check terminals for contact resistance, corrosion and deformation.

(2)

Check connecting condition of ECM and component connector : Check terminal separation, damage of locking device and connecting condition between terminal and wiring.

note

Disconnect the pin which requires checking at male connector and insert it to the terminal at female connector for checking connecting condition. (After checking, reconnect the pin at correct position.)

3.

Is the problem found?

	▶ Repair the trouble causing part and go to "Verification of Vehicle Repair" procedure.
	▶ Go to "Power Circuit Inspection".

1.

IG key OFF.

2.

Disconnect 'FUEL PUMP RELAY'.

3.

IG key ON.

4.

Check voltage between 'SNSR 2 FUSE 15A' (85) terminal of 'FUEL PUMP RELAY' harness connector and chassis ground.

5.

Check voltage between 'F/PUMP FUSE 20A' (30) terminal of 'FUEL PUMP RELAY' harness connector and chassis ground.

Specification : 10.5V ~ 14.5V

note

To view Flash content, you need to install the appropriate browser extension

6.

Is the measured value within specification?

▶ Go to "Control Circuit Inspection".

▶ If no voltage is detected,

☞ Repair open / short to ground between 'SNSR 4 FUSE 15A' (85) terminal of 'FUEL PUMP RELAY' harness connector and 'SNSR 4 FUSE 15A' terminal of 'E/R JUNCTION BOX' harness connector, and go to "Verification of Vehicle Repair" procedure.

☞ Repair open / short to ground between 'F/PUMP FUSE 15A (30)' terminal of 'FUEL PUMP RELAY' harness connector and 'F/PUMP FUSE 15A' terminal of 'E/R JUNCTION BOX' harness connector, and go to "Verification of Vehicle Repair" procedure.

▶ If the voltage is high than specification value,

☞ Repair short to battery between SNSR 4 FUSE 15A' (85) terminal of 'FUEL PUMP RELAY' harness connector and 'SNSR 4 FUSE 15A' terminal of 'E/R JUNCTION BOX' harness connector, and go to "Verification of Vehicle Repair" procedure.

☞ Repair short to battery between 'F/PUMP FUSE 15A (30)' terminal of 'FUEL PUMP RELAY' harness connector and 'F/PUMP FUSE 15A' terminal of 'E/R JUNCTION BOX' harness connector, and go to "Verification of Vehicle Repair" procedure.

1.

IG key OFF.

2.

Disconnect 'FUEL PUMP RELAY'.

3.

IG key ON.

4.

Check voltage between 'Fuel pump relay control' (86) terminal of 'FUEL PUMP RELAY' harness connector and chassis ground.

Specification : 3.2V ~ 3.7V

note

To view Flash content, you need to install the appropriate browser extension

5.

Is the measured value within specification?

▶ Go to "Component Inspection" procedure.

▶ If no voltage is detected, go to "Check open in control circuit" as follows.

▶ If the voltage is high than specification value, repair short to battery between 'Fuel pump relay control' (86) terminal of 'FUEL PUMP RELAY' and 'Fuel pump relay control' terminal of ECM harness connector, and go to "Verification of Vehicle Repair" procedure.

6.

IG key OFF.

7.

Disconnect 'FUEL PUMP RELAY' and ECM connector.

8.

Check resistance between 'Fuel pump relay control' (86) terminal of 'FUEL PUMP RELAY' harness connector and 'Fuel pump relay control' terminal of ECM harness connector.

Specification : Continuity (Below 1.0Ω)

note

To view Flash content, you need to install the appropriate browser extension

9.

Is the measured value within specification?

	▶ Repair short to ground between 'Fuel pump relay control' (86) terminal of 'FUEL PUMP RELAY' harness connector and 'Fuel pump relay control' (86) terminal of ECM harness connector, and go to "Verification of Vehicle Repair" procedure.
	▶ Repair open between 'Fuel pump relay control' (86) terminal of 'FUEL PUMP RELAY' harness connector and 'Fuel pump relay control' (86) terminal of ECM harness connector, and go to "Verification of Vehicle Repair" procedure.