2.
Install the split pin (A) and the castle nut (B) to the rear upper arm ball joint (C).
Tightening torque Nm (kgf-m, lb-ft) :
78.5~88.3 (8.0~9.0, 57.9~65.1)
Install the rear axle carrier assembly.
Install the split pin (A) and the castle nut (B) to the rear upper arm ball joint (C).
Tightening torque Nm (kgf-m, lb-ft) :
78.5~88.3 (8.0~9.0, 57.9~65.1)
Install the wheel speed sensor (A) and the parking brake cable (B) to the rear axle carrier.
Tightening torque Nm (kgf-m, lb-ft) :
Wheel speed sensor (A) :
6.9~10.8 (0.7~1.1, 5.1~8.0)
Install the brake caliper (B), then tighten the brake caliper mounting bolts (A).
Tightening torque Nm (kgf-m, lb-ft) :
63.7~73.5 (6.5~7.5, 47.0~54.2)
Install the rear stabilizer link (A) from the rear axle carrier.
Tightening torque Nm (kgf-m, lb-ft) :
Nut(B) : 58.8~78.5 (6.0~8.0, 43.4~57.9)
Install the assist arm (A) and the trailing arm (B) to the rear axle carrier.
Tightening torque Nm (kgf-m, lb-ft) :
Bolt (C) : 137.3~156.9 (14~16, 101.3~115.7)
Nut (D) : 98.1~117.7 (10~12, 72.3~86.8)
Nut (E) : 137.3~156.9 (14~16, 101.3~115.7)
Bolt (F) : 137.3~156.9 (14~16, 101.3~115.7)
After checking the distance(453±10mm(17.83±0.39in)) between the wheel housing garnish(A) and the hub assembly(B) as shown in the illustration, tighten the mounting bolts and nuts of rear chassis part with specified torque.
Install the rear shock absorber (A).
Tightening torque Nm (kgf-m, lb-ft) :
Bolt (B) : 137.3~156.9 (14~16, 101.3~115.7)
Nut (C) : 98.1~117.7 (10.0~12.0, 72.3~86.8)
Install the spring (A), the upper pad (B) and the lower pad (C).
Install the mounting bolt (B) of the rear lower arm(A) and the rear carrier with a specified torque, while supporting the lower arm (A) with a jack as shown in the illustration. Tighten the mounting bolt (C) of the cross member and the rear lower arm with a specified torque.
Tightening torque Nm (kgf-m, lb-ft) :
Bolt (B) : 137.3~156.9 (14~16, 101.3~115.7)
Nut (C) : 137.3~156.9 (14~16, 101.3~115.7)
Install the washer (C), castle nut (B) and split pin (A) to the rear hub assembly.
Tightening torque Nm (kgf-m, lb-ft) :
196.1~255.0 (20~26, 144.7~188.1)
The washer (B) should be assembled with convex surface outward when installing the castle nut (A) and split pin (C).
Install the wheel and tire (A) to the rear hub (B).
Tightening torque Nm (kgf-m, lb-ft) :
88.3~107.9 (9~11, 65.1~79.6)
Be careful not to damage the hub bolts (C) when installing the rear wheel and tire (A).
