2.
Remove the front wheel and tire (A) from the front hub (B).
caution
Be careful not to damage to the hub bolts (C) when removing the front wheel and tire (A).
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
Remove the front wheel and tire (A) from the front hub (B).
Be careful not to damage to the hub bolts (C) when removing the front wheel and tire (A).
Remove the front stabilizer link (A) from the strut assembly.
Remove the split pin and front lower arm mounting bolt (B) from the knuckle (A).
Remove the under cover (A).
Remove the connecting bolt (A) between the steering universal joint assembly and the pinion shaft.
Keep the neutral-range to prevent the damage of the clock spring inner cable when you handlethe steering wheel.
Disconnect the EPS connector (B).
Remove the front muffler (A).
Remove the front roll stopper mounting bolts (A).
Remove the rear roll stopper mounting bolts (A).
Remove the sub frame stay mounting bolts (A), nuts (B) and the sub frame mounting bolts (C) by supporting it with a jack.
Put SST(09624-38000) on the jack (A) then fix bolts (B-2ea).
Sub frame (A) as using SST(09624-38000) then remove bolt and nut.
Remove the stabilizer bar bracket (A) mounting bolts (B) from the sub frame.
Remove the stabilizer bar.
Install the bushing (B) on the stabilizer bar (A).
Bring clamp (C) of stabilizer bar (A) into contact with bushing (B).
Install the bracket on the bushing (B).
Install the stabilizer bar to the sub frame.
Install the stabilizer bar bracket (A) mounting bolts (B).
Tightening torque
Bolt(B)
: 49.0 ~ 63.7N.m (5.0 ~ 6.5kgf.m, 36.2 ~ 47.0lb-ft)
Install the sub frame (A) by supporting it with a jack.
Install the sub frame stay mounting bolts(A), nuts(B) and the sub frame mounting bolts(C).
Tightening torque
Bolt(A)
: 68.6 ~ 88.3 N.m (7.0 ~ 9.0kgf.m, 50.6 ~ 65.1lb-ft)
Nut(B)
: 68.6 ~ 88.3 N.m (7.0 ~ 9.0kgf.m, 50.6 ~ 65.1lb-ft)
Bolt(C)
: 137.3 ~ 156.9N.m (14 ~ 16kgf.m, 101.3 ~ 115.7lb-ft)
Install the front roll stopper mounting bolts (A).
Tightening torque
Bolt(A)
: 49.0 ~ 63.7N.m (5.0 ~ 6.5kgf.m, 36.2 ~ 47.0lb-ft)
Bolt(B)
: 78.5 ~ 98.1N.m (8.0 ~ 10.0kgf.m, 57.9 ~ 72.3lb-ft)
Install the rear roll stopper mounting bolts (A).
Tightening torque
Bolt(A)
: 49.0 ~ 63.7N.m (5.0 ~ 6.5kgf.m, 36.2 ~ 47.0lb-ft)
Install the front muffler (A).
Tightening torque
: 39.2 ~ 58.8N.m (4.0 ~ 6.0kgf.m, 28.9 ~ 43.4lb-ft)
Install the connecting bolt (A) between the steering universal joint assembly and the pinion shaft.
Tightening torque
: 29.4 ~ 44.1N.m (3.0 ~ 4.5kgf.m, 21.7 ~ 32.5lb-ft)
Reconnect the EPS connector (B).
Install the under cover (A).
Tightening torque
: 16.7 ~ 25.5N.m (1.7 ~ 2.6kgf.m, 12.3 ~ 18.8lb-ft)
Install the split pin and front lower arm mounting bolt (B) to the knuckle (A).
Tightening torque
: 98.1 ~ 117.7N.m (10.0 ~ 12.0kgf.m, 72.3 ~ 86.8lb-ft)
Install the front stabilizer link (A) to the strut assembly.
Tightening torque
Nut(B)
: 98.1 ~ 117.7N.m (10.0 ~ 12.0kgf.m, 72.3 ~ 86.8lb-ft)
Install the wheel and tire (A) to the front hub (B).
Tightening torque
: 88.3 ~ 107.9N.m (9 ~ 11kgf.m, 65.1 ~ 79.6lb-ft)
Be careful not to damage the hub bolts (C) when installing the front wheel and tire (A).
Check the bushing for wear and deterioration.
Check the stabilizer bar for bending or breakage.
Check the ball joint dust cover for cracks.
Check all bolts.
