Install the rear axle carrier(A).
Install the strut mounting nuts(D).
Tightening torque
140 ~ 160Nm (1400 ~ 1600Kgf.cm, 103.3 ~ 118.0lbf.ft)
Install the suspension arm mounting nut(C).
Tightening torque
160 ~ 180Nm (1600 ~ 1800Kgf.cm, 118.0 ~ 132.8lbf.ft)
Install the trailing arm mounting bolt(B).
Tightening torque
100 ~ 120Nm (1000 ~ 1200, 73.8 ~ 88.5lbf.ft)
Replace the self-locking nut with new ones after removal.
Install the rear dust cover(B) and then tighten the mounting bolts(A).
Tightening torque
50 ~ 60Nm (500 ~ 600Kgf.cm, 36.9 ~ 44.3lbf.ft)
Install the hub assembly(B) and hub washer(A).
After tightening the hub bearing flange nut(A), caulk the concave portion(B) of the spindle by crimping the nut.
Tightening torque
200 ~ 260Nm (2000 ~ 2600Kgf.cm, 147.5 ~ 191.8lbf.ft)
Replace the flange nut with new ones after removal.
Install the hub cap(A).
Replace the hub cap with new ones after removal.
Installation of the rear speed sensor(A).(For vehicles equipped with ABS):
Insert a feeler gauge(C) into the space between the pole piece of the speed sensor(A) and the rotor teeth(B) surface, and then tighten the speed sensors(A) at the position where the clearance at all places is within the standard value.
Standard value
Clearance : 0.5 ~ 1.5mm (0.02 ~ 0.06in.)
Install the brake disc(C) from the hub(B), then tighten the brake disc mounting screw(A).
Tightening torque
5 ~ 6Nm (50 ~ 60, 3.7 ~ 4.4lbf.ft)
Install the brake caliper(B), then tighten the mounting bolt(A).
Tightening torque
50 ~ 60Nm (500 ~ 600Kgf.cm, 36.9 ~ 44.3lbf.ft)
Install the rear wheel and tire(A) on the rear hub(B).
Tightening torque
90 ~ 110Nm (900 ~ 1100kgf.cm, 66.4 ~ 81.2lbf.ft)
Be careful not to damage the hub bolts(C) then install the rear wheel and tire(A).
Install the rear axle carrier(A).
Install the strut mounting nuts(D).
Tightening torque
140 ~ 160Nm (1400 ~ 1600Kgf.cm, 103.3 ~ 118.0lbf.ft)
Install the suspension arm mounting nut(C).
Tightening torque
160 ~ 180Nm (1600 ~ 1800Kgf.cm, 118.0 ~ 132.8lbf.ft)
Install the trailing arm mounting bolt(B).
Tightening torque
100 ~ 120Nm (1000 ~ 1200Kgf.cm, 73.8 ~ 88.5lbf.ft)
Replace the self-locking nut with new ones after removal.
Install the rear dust cover(B), then tighten the mounting bolt(A).
Tightening torque
50 ~ 60Nm (500 ~ 600Kgf.cm, 36.9 ~ 44.3lbf.ft)
Install the rear hub assembly(B) and hub washer(A).
After tightening the hub bearing flange nut(A), caulk the concave portion(B) of the spindle by crimping the nut.
Tightening torque
200 ~ 260Nm (2000 ~ 26000Kgf.cm, 147.5 ~ 191.8lbf.ft)
Replace the flange nut with new ones after removal.
Install the hub cap(A).
Replace the hub cap with new ones after removal.
Install the brake drum(C) from the hub(B), then tighten the brake drum mounting screw(A).
Tightening torque
5 ~ 6Nm (50 ~ 60Kgf.cm, 3.7 ~ 4.4lbf.ft)
Install the rear wheel and tire(A) on the rear hub(B).
Tightening torque
90 ~ 110Nm (900 ~ 1100Kgf.cm, 66.4 ~ 81.2lbf.ft)
Be careful not to damage the hub bolts(C) then install the rear wheel and tire(A).
