The amount of intake air flow must be inputted to ECM in order to determine the fuel injection quantity. MAPS(Manifold Absolute Pressure) calculates the amount of air indirectly as measuring the pressure inside of intake manifold. This mechanism is also called Speed-Density Type. MAPS transfers analog output signal which is proportional to the change of intake manifold pressure, then, with this signal and RPM, ECM calculates the amount of intake air flow. MAPS is mounted on surge tank to measure the pressure inside of intake manifold, and it consists of a piezo electric element and hybrid IC which amplifies output signal from the element. A piezo electric element is a sort of a diaphragm using piezo electric effect. One side of the diaphragm is surrounded with vacuum chamber while intake pressure is applied to the other side. Thus, signals are outputted by the transformation of diagphragm according to the change of pressure inside of intake manifold.

If sensor signal input is higher than 4.88V during 5 sec, ECM sets DTC P0108.

As often as possible, the MAPS signal should be compared with the TPS signal. Check whether the MAPS and TPS signals increase at the same time when accelerating. During acceleration, the MAPS output voltage increases; during deceleration, the MAPS output voltage decreases.

4.

Read "DTC Status" parameter

5.

Is parameter displayed "History(Not Present) fault"?

note

History (Not Present) fault : DTC occurred but has been cleared.

Present fault : DTC is occurring at present time.

	▶ Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to "Verification of Vehicle Repair" procedure.
	▶ Go to next step as below.

3.

Has a problem been found?

	▶ Repair as necessary and go to "Verification of Vehicle Repair" procedure.
	▶ Go to next step as below

1.

Check short to battery in harness.

(1)

IG "OFF".

(2)

Disconnect MAPS and ECM connector.

(3)

IG "ON" & Eng. "OFF"

(4)

Measure voltage between terminal 1 of the MAPS harness connector and chassis ground.

Specification : 0V

(5)

Is the measured voltage within specification ?

	▶ Go to next step as below
	▶ Repair or replace as necessary and then, go to "Verification of Vehicle Repair" procedure.

2.

Measure resistance between terminal 4 of MAPS harness connector and chassis ground.

Specification : Below 1Ω

3.

Is the measured resistance within specification ?

	▶ Go to next step as below
	▶ Repair or replace as necessary and then, go to "Verification of Vehicle Repair" procedure.

1.

Check MAPS performance.

(1)

IG "OFF".

(2)

Connnect CH A probe to terminal 1 of MAPS and CH B probe to terminal 1 of TPS connector.

(3)

Warm up the engine to normal operating temperature.

(4)

Measure signal waveform of MAPS and TPS together by stepping on and off the accellerator pedal.

Specification

Pressure (kPa)	Approx. 20	Approx. 35	Approx. 60	Approx. 95	Approx. 101
Voltage(V)	Approx. 0.7~0.8	Approx. 1.3~1.4	Approx. 2.3~2.4	Approx. 3.7~3.8	Approx. 3.9~4.1

(5)

Is the measured signal waveform(Comparison response of TPS with MAPS) O.K ?

	▶ Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage. Repair or replace as necessary and go to "Verification of Vehicle Repair" procedure.
	▶ Substitute with a known - good MAPS and check for proper operation. If the problem is corrected, replace MAPS and go to "Verification of Vehicle Repair" procedure.

After a repair, it is essential to verify that the fault has been corrected.

4.

Is parameter displayed "History(Not Present) fault"?

	▶ System performing to specification at this time. Clear the DTC
	▶ Go to the applicable troubleshooting procedure.