1.
Using a screwdriver or remover, remove the front door quadrant inner cover (A).
Be careful not to scratch the door trim and other parts.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the front door quadrant inner cover (A).
After loosening the mounting screws, then remove the front door trim (A).
Remove the inside handle cage (A).
Disconnect the connectors (A).
Install in the reverse of removal.
Make sure connectors are connected properly and each rod is connected securely.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Remove the front door trim.
After loosening the mounting screws, then remove the inside handle (A).
Install in the reverse of removal.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Remove the front door trim.
Remove the front door belt inside weatherstrip (A).
Remove the glass mounting hole plug (B).
Use the door switch to align the mounting hole/bolt with the hole in the door.
If unable to operate the window motor, remove the motor and align the hole by hand.
Be careful not to drop the glass and/or scratch the glass surface.
Carefully adjust the glass (A) until you can see the bolts, then loosen them. Separate the glass from the glass run and carefully pull the glass out through the window slot.
Tightening torque :
3.9 ~ 2.9 N.m (0.4 ~ 1.2 kgf.m, 11.8 ~ 8.7 lb-ft)
Install in the reverse of removal.
Roll the glass up and down to see if it moves freely without binding.
Adjust glass position as needed.
Make sure the door lock and opens properly.
Replace any damaged clips.
Remove the front door trim.
Disconnect the speaker connector (B).
After loosening the mounting screws, then remove the speaker (A).
Install in the reverse of removal.
Use sheet metal screws to secure the speaker.
Replace any damaged clips.
Make sure the door locks/unlocks and opens/closes properly.
Make sure connectors are connected properly and each rod is connected securely.
Remove the front door trim.
Disconnect the power window motor connector (B).
After loosening the mounting screws, then remove the power window motor (A).
Install in the reverse of removal.
Grease should be applied to areas where there is rotational parts and springs.
Roll the glass up and down to see if it moves freely without binding.
Replace any damaged clips.
Make sure the door locks/unlocks and opens/closes properly.
Remove the following parts:
Front door trim
Window glass
Outside handle
Loosen the mounting bolt (A).
Disconnect the front door main connector (A).
After loosening the door module mounting bolts, then remove the front door module (A).
Tightening torque:
6.9~10.8 N.m (0.7~1.1 kgf.m, 5.1~8.0 lb-ft)
Disconnect the connectors and door module wiring harness (A).
Install in the reverse of removal.
The area of whole parts should be applied with sufficient grease.
Make sure connectors are connected properly and each rod is connected securely.
Make sure the door locks/unlocks and opens/closes properly.
Remove the front door trim.
Remove the hole plug (B).
After loosening the mounting bolt, then remove the outside handle cover (A).
Tightening torque:
0.7 ~ 0.5 N.m (0.07 ~ 0.1 kgf.m, 1.0 ~ 0.7 lb-ft)
Remove the outside handle (A) by sliding it rearward.
Disconnect the outside handle connector (A).
Install in the reverse of removal.
Make sure the door locks/unlocks and opens/closes properly.
Make sure the door locks and opens properly.
Remove the following items :
Front door trim
Window glass
Outside handle
Loosen the mounting bolt (A).
Disconnect the front door main connector (A).
After loosening the door module mounting bolts, then remove the front door module (A).
Tightening torque:
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Remove the door latch wiring (A).
Disconnect the connector (B).
Remove the front door latch assembly (A).
Install in the reverse of removal.
Make sure the connector is connected properly.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Loosen the checker mounting bolts.
Detach the clips, then remove the front door side weatherstrip (A).
Install in the reverse of removal.
Replace any damaged clips.
