1.
Using a screwdriver or remover, remove the cluster fascia upper pannel (A).
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the cluster fascia upper pannel (A).
Using a screwdriver or remover, remove the shroud upper cover (A).
After loosening the mounting screws, then remove the cluster assembly (A).
Disconnect the connector (A).
Install in the reverse of removal.
Make sure the connectors are connected in properly.
Replace any damaged clips.
A plastic trim tool is recommended, but if prying with a screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the crash pad center garnish (A).
After loosening the mounting screws, then remove the center fascia panel (A).
Disconnect the connector (A).
Install in the reverse of removal.
Make sure the connectors are connected in properly.
Replace any damaged clips.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the crash pad side cover (A).
Using a screwdriver or remover, remove the relay box cover (A).
Disconnect the connector (A).
After loosening the mounting screws, then remove the crash pad lower panel (A).
Install in the reverse of removal.
Make sure the connectors are connected in properly.
Replace any damaged clips.
A plastic trim tool is recommended, but if prying with a screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the crash pad center garnish (A).
After loosening the mounting screws, then remove the center fascia panel (A).
Disconnect the connector (A).
After loosening the mounting screws, then remove the audio assembly (A).
Disconnect the connectors.
Install in the reverse of removal.
Make sure the connectors are connected in properly.
Replace any damaged clips.
A plastic trim tool is recommended, but if prying with a screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the crash pad center garnish (A).
After loosening the mounting screws, then remove the center fascia panel (A).
Disconnect the connector (A).
After loosening the mounting screws, then remove the audio assembly (A).
Disconnect the connectors.
After loosening the mounting screws, then remove the heater control unit (A).
Disconnect the connectors (A) and hose (B).
Install in the reverse of removal.
Make sure the connectors are connected in properly.
Replace any damaged clips.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the crash pad side cover (A).
Disconnect the guide (B) from the glove box (A).
Disconnect the lift (A) from the glove box (B).
Disconnect the pin (A) and then remove the glove box (B).
After loosening the mounting screw, then remove the center crash pad passenger's panel (A).
After loosening the mounting screws and bolts, then remove the glove box housing (A).
Install in the reverse of removal.
Make sure the connectors are connected in properly.
Replace any damaged clips.
After loosening the mounting screws, then remove the shroud assembly (A).
Install in the reverse of removal.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the crash pad side cover (A).
Install in the reverse of removal.
Replace any damaged clips.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Remove the following items.
Front seat
(Refer to the BD group – “Front Seat”)
Front pillar trim
(Refer to the BD group – “Interior Trim”)
Floor console assembly
(Refer to the BD group – “Console”)
Front door scuff trim
(Refer to the BD group – “Interior Trim”)
Cowl side trim
(Refer to the BD group- Interior Trim”)
Crash pad center garnish
Crash pad side cover
Crash pad lower panel
Cluster fascia upper panel & Cluster assembly
Center fascia panel
Audio assembly
Heater control unit
Center crash pad passenger's panel
Glove box & Glove box housing
Steering column
(Refer to the ST group - "Steering Column and Shaft")
After loosening the mounting screw, nut, clip, then remove the console side cover (A).
Disconnect the connector (A).
After loosening the mounting screw, then remove the center crash pad passenger's panel (A).
Using a screwdriver or remover, remove the center crash pad driver's panel [RH] (A).
Disconnect the connector (A).
After loosening the mounting screws, then remove the center crash pad driver's panel [LH] (A).
Disconnect the connectors (A).
Disconnect the passenger`s airbag connector (A).
Loosen the mounting bolts.
Using a screwdriver or remover, remove the photo sensor (A).
Disconnect the photo sensor connector (B).
Disconnect the connector (A).
After loosening the mounting bolts and nuts, screw, then remove the main crash pad assembly (A).
Install in the reverse of removal.
Make sure the crash pad fits onto the guide pins correctly.
Before tightening the bolts, make sure the crash pad wire harnesses are not pinched.
Make sure the connectors are plugged in properly, and the antenna lead is connected properly.
Enter the anti- theft code for the radio, then enter the customer`s radio station presets.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Remove the following items.
Front seat
(Refer to the BD group – “Front Seat”)
Floor console assembly
(Refer to the BD group – “Console”)
Cowl top cover
(Refer to the BD group - "Cowl Top Cover")
Main crash pad
Disconnect the blower unit connectors.
(Refer to the HA group - "Air conditioning system, Heater, Blower")
Disconnect the multi box connectors.
Disconnect the multi box connectors.
Disconnect the passenger compartment junction box connectors.
Disconnect the airbag control module (SRSCM) connectors (A).
Disconnect the connector (A) and the mounting clips in the front pillar.
After loosening the mounting bolts and nuts, then remove the cowl cross bar assembly (A).
Install in the reverse of removal.
Make sure the connectors are connected in properly.
Replace any damaged clips.
