1.
Using the Valve Guide installer push rod, push the valve guide out toward the cylinder block with a press.
Check the valve spring free length and tension. If they exceed the service limit, replace the spring.
Using a square, test the squareness of each spring.
If a spring is excessively out of square, replace it.
Standard vlaue
Free height
1.3 L : 42.03 mm (1.655 in.)
1.1 L : 40.50 mm (1.594 in.)
Load
1.3 L : 24.7 kg at 34.5 mm
1.1 L : 15.60 ± 0.9 kg/32.0 mm
Out of square : 1.5° or less
Check the valve stem-to-guide clearance. If the clearance exceeds the service limit, replace the vlave guide with the next oversize part.
Standard vlaue
Intake
1.3 L : 0.030 ~ 0.060 mm (0.0012 ~ 0.0024 in.)
1.1 L : 0.020 ~ 0.047 mm (0.0008 ~ 0.0018 in.)
Exhaust
1.3 L : 0.035 ~ 0.065 mm (0.0014 ~ 0.0026 in.)
1.1 L : 0.050 ~ 0.082 mm (0.0019 ~ 0.0032 in.)
Size mm (in.) | Size mark | Cylinder head hole size mm (in.) |
0.05 (0.002) O.S. | 5 | 11.05 ~ 11.058 (0.435 ~ 0.4354) |
0.25 (0.010) O.S. | 25 | 11.25 ~ 11.258 (0.429 ~ 0.4432) |
0.50 (0.020) O.S. | 50 | 11.50 ~ 11.508 (0.4528 ~ 0.4531) |
Size mm (in.) | Size mark | Cylinder head hole size mm (in.) |
0.05 (0.002) O.S. | 5 | 10.05 ~ 10.068 (0.395 ~ 0.396) |
0.25 (0.010) O.S. | 25 | 1.025 ~ 10.268 (0.403 ~ 0.404) |
0.50 (0.020) O.S. | 50 | 10.50 ~ 10.518 (0.413 ~ 0.414) |
The valve guide is installed using a press fit. Using Value Guide installer (09221-21200 A/B (1.3L), 09222-02100 (1.1L)) or suitable tool, replace the valve guide described in the following procedure.
Using the Valve Guide installer push rod, push the valve guide out toward the cylinder block with a press.
Machine the valve guide insert hole in the cylinder head to the specified oversize of the new valve guide.
Using the Valve Guide installer or suitable tool, press fit the valve guide. Using the vlalve guide installer makes it possinle to press fit the valve guide to a predetermined height. Install the vlave guide from the top of the cylinder head. Note that intake and exhaust valve guides differ in length.
After installing the valve guides, insert new valves and check the clearance.
Whenever valve guides are replaced, check for valve-to-seat contact, and recondition the valve seats as necessary.
Any valve seat insert that has been worn over the service limit should be removed at normal temperature after cutting away most of the insert wall, using valve seat cutters, as shown in Fig A.
After removing the seat insert, machine the seat insert bore using a reamer or a cutter. Cut to the size shown in the table.
Heat the cylinder head to about 250°C (480°F) and press in the oversize seat insert. The oversize seat insert should be at normal room temperature for installation. After installing a new valve seat insert, resurface the valve seat using the same procedure described in the first paragraph of "Valve Seat Insert" (above).
Description | Size mm (in.) | Size mark | Seat insett height H mm (in.) | Cylinder head I.D. mm (in.) |
Intake valve seat insert | 0.3 (0.012) O.S. | 30 | 5.1~5.3 (0.201~0.2069) | 28.80~28.821(1.134~1.135) |
0.6(0.024) O.S. | 60 | 5.4~5.6 (0.213~0.220) | 29.10~29.121(1.146~1.147) | |
Exhaust valve seat | 0.3 (0.012) O.S. | 30 | 5.9~6.1 (0.232~0.240) | 34.30~34.325(1.350~1.351) |
0.6 (0.024) O.S. | 60 | 6.2~6.4(0.244~0.252) | 34.60~34.625(1.362~1.363) |
Description | Size mm (in.) | Size mark | Seat insett height H mm (in.) | Cylinder head I.D. mm (in.) |
Intake valve seat insert | 0.3 (0.012) O.S. | 30 | 6.2~6.4 (0.244~0.252) | 24.30~24.321(0.957~0.958) |
0.6(0.024) O.S. | 60 | 6.5~6.7 (0.0256~0.264) | 24.60~24.621(0.968~0.969) | |
Exhaust valve seat | 0.3 (0.012) O.S. | 30 | 6.2~6.4 (0.244~0.252) | 29.30~29.321(1.153~1.154) |
0.6 (0.024) O.S. | 60 | 6.5~6.7(0.256~0.264) | 29.60~29.621(1.165~1.166) |
Check each valve for wear, damage and distortion of head and stem at B. Repair or correct, if necessary. If stem end A is pitted or worn, resurface as necessary. This correction must be limited to a minimum. Also resurface the valve face.
MARGIN
Standard value
Intake
1.3 L : 1.1 mm (0.043 in.)
1.1 L : 0.8 mm (0.031 in.)
Exhaust
1.3 L : 1.4 mm (0.055 in.)
1.1 L : 1.2 mm (0.047 in.)
Limit
Intake
1.3 L : 0.8 mm (0.031 in.)
1.1 L : 0.5 mm (0.019 in.)
Exhaust
1.3 L : 1.1 mm (0.043 in.)
1.1 L : 0.9 mm (0.035 in.)
