1.
Remove the quadrant inner cover (A).
Take care not to scratch the door trim and other parts.
Put on gloves to protect your hands.
Remove the quadrant inner cover (A).
Remove the inside handle cover (A).
Loosen the door trim (F) mounting screws. Release the clips that hold the door trim, then remove the door trim by pulling it upward. Disconnect the power window switch connector (A), power mirror connector (B), and door courtesy lamp connector (C), trunk lid connector (D).
Installation is the reverse of removal.
Make sure of connectors is plugged in properly and each rod is connected securely.
Make sure the door lock and opens properly.
Remove the front door trim.
Remove the glass mounting hole plug (A).
Using the door switch to align the mounting hole with the hole on the door glass.
If it is impossible, align the hole with hands after removing the motor.
Take care not to drop to glass and scratch the glass surface.
Carefully move the glass (B) until you can see the bolts, then loosen them. Separate the glass from the glass run and carefully pull the glass out through the window slot.
Installation is the reverse of removal.
Roll the glass up down to see if it move freely without binding.
Adjust the position of the glass as necessary
Remove the door trim.
After disconnecting the connector (A), remove the power window motor (B).
Installation is the reverse of removal.
Roll the glass up down to see if it move freely without binding.
Loosen the mounting bolt, then remove the key holder (A).
Remove the outside handle (A).
Installation is the reverse of removal.
Remove the following parts.
Front door trim.
Glass.
Out side handle.
Remove the outside handle pad (A).
Remove the inside handle.
Remove the latch assembly.
Remove the outside support bracket (A).
After disconnecting the cable (A), remove the outside handle base (B).
Installation is the reverse of removal.
Make sure the door lock and open properly.
Remove the following parts.
Front door trim.
Glass.
Inside handle.
Outside handle.
Loosen the door module mounting bolts, then remove the door module (A).
Remove the clips.
Disconnect the door module wiring harness (A), then remove the module assembly (B).
Installation is the reverse of removal.
Make sure the connector is plugged in properly and each rod is connected securely.
Make sure the door lock and open properly.
Remove the front door trim.
Loosen the inside handle (A) mounting screws.
Remove the space (D).
Disconnect the lock cable (A) and inside connect cable (B).
Remove the inside handle (C).
Installation is the reverse of removal.
Make sure the door locks and open properly.
Remove the following parts.
Front door trim.
Glass.
Inside handle.
Out side handle.
Remove the module assembly.
Disconnect the latch connector (A), then remove the latch assembly (B).
Installation is the reverse the removal.
Make sure the door locks and opens properly.
Loosen the mounting screw, then remove the door belt weatherstrip (A).
Installation is the reverse of removal.
Remove the front door trim.
Loosen the mounting screws (A).
Remove the power window switch (A).
Installation is the reverse the removal.
Loosen the checker mounting bolts.
Detach the clips, then remove the weatherstrip (A).
Installation is the reverse of removal.
Remove the front door scuff trim.
Remove the weatherstrip (A).
Installation is the reverse of removal.
Check the glass run channel for damage or deterioration, and replace them necessary.
Remove the following parts.
Quadrant cover.
Door trim.
Carefully move the glass (A) until you can see the glass mounting bolts (B), then loosen them.
Check that the glass moves smoothly.
Raise the glass fully, and check for gaps.
Check that the glass contacts the glass run channel Evenly.
Check for water leaks. Run water over the roof and on the sealing area as shown, and note these items:
Use a 12mm (1/2Iin.) diameter hose (A).
Adjust the rate of water flow as shown (B).
Do not use a nozzle.
Hold the hose about 300mm(12in.) away from The door (C).
After installing the door, check for a flush fit with the Body, then check for equal gaps between the front, Rear, and bottom, door edges and the body. Check That the door and body edges are parallel. Before Adjusting, replace the mounting bolts.
Place the vehicle on a firm, level surface when adjusting the doors.
Adjust at the hinges (A):
Loosen the door mounting bolts (B) slightly, and move the door IN or OUT until it aligns flush with the body.
Loosen the hinge mounting bolts (C) slightly, and move the door BACKWARD or FORWARD, UP or DOWN as necessary to equalize the gaps.
Place a shop towel (D) on the jack (E) to prevent damage to the door when adjusting the door.
Check that the door and body edges are parallel.
Grease the pivot portions of the hinges indicated by the arrows.
Check for water leaks.
