2.
Remove the rear wheel and tire (A) from rear hub .
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)
note
Be careful not to damage to the hub bolts when removing the rear wheel and tire (A).
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
Remove the rear wheel and tire (A) from rear hub .
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)
Be careful not to damage to the hub bolts when removing the rear wheel and tire (A).
Loosen the mount screw and then brake disc (A).
Tightening torque:
4.9 ~ 6.8 N.m (0.5 ~ 0.7 kgf.m, 3.6 ~ 5.0 lb-ft)
Loosen the bolt & nut and then disconnect the shock absorber (A) with the rear axle.
Tightening torque :
137.3~156.9N.m(14.0~16.0Kgf.m, 101.3~115.7lb-ft)
When removing the bolt, remove the shock absorber in no-load condition by using the transmission jack.
Loosen the bolt & nut and then saperate the rear upper arm (A).
Tightening torque:
137.2 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.2 ~ 115.7 lb-ft)
Must be separate the upper arm & upper arm mounting bolt at the rear carrier assembly before remove the rear brake caliper.
When removing the bolt, remove the upper arm in no-load condition by using the transmission jack.
Disconnect the parking brake connector (A).
Remove the brake caliper mounting bolts, and then place the brake caliper assembly (B) with wire as shown in the illustration.
Tightening torque:
49.0 ~ 58.8 N.m (5.0 ~ 6.0 kgf.m, 36.2 ~ 43.4lb-ft)
Disconnect the wheel speed sensor connector (A).
Tightening torque:
6.8 ~ 10.7 N.m (0.7 ~ 1.1 kgf.m, 2.8 ~ 7.9 lb-ft)
Loosen the trailing arm mounting nut, and then remove the trailing arm (A).
Tightening torque:
44.1 ~ 53.9 N.m (4.5 ~ 5.5 kgf.m, 32.5 ~ 39.7 lb-ft)
Remove the assist arm (A).
Remove the split pin (B).
Remove the nut (C).
Tightening torque:
78.5 ~ 98.0 N.m (8.0 ~ 10.0 kgf.m, 57.9 ~ 72.3 lb-ft)
Loosen the lower arm (A) and rear strut (B) mounting bolts and remove the knuckle assembly (C).
Tightening torque:
Lower arm : 137.2 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.2 ~ 115.7 lb-ft)
Strut : 137.2 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.2 ~ 115.7 lb-ft)
Loosen the hub bearing mounting, and then remove the hub bearing from knuckle (A).
Tightening torque:
58.8 ~ 68.6 N.m (6.0 ~ 7.0 kgf.m, 43.4 ~ 50.6 lb-ft)
Install in the reverse order of removal.
Check the hub for cracks and the splines for wear.
Check the brake disc for scoring and damage.
Check the rear axle carrier for cracks.
Check the bearing for cracks or damage.
