2.
After loosening the front seat assembly mounting bolts, remove the front seat assembly (A).
Tightening torque :
34.3 ~ 53.9 N.m (3.5 ~ 5.5 kgf.m, 25.3 ~39.8 lb-ft)
Remove the front foot cover.
After loosening the front seat assembly mounting bolts, remove the front seat assembly (A).
Tightening torque :
34.3 ~ 53.9 N.m (3.5 ~ 5.5 kgf.m, 25.3 ~39.8 lb-ft)
Disconnect the airbag connector (A), power seat connector (B), seat buckle connector (C).
[Driver's]
[Passenger's]
Install in the reverse order of removal.
Seat Mounting Bolt Installation Procedure
Set the into the most rearward position. Check then each slide is locked, and then Tighten the front mounting bolt temporarily.
Set the seat into most forward position. Check that each slide is locked, and then Tighten the rear mounting bolt completely.
Set the seat into the most rearward position. Check the front mounting bolt completely.
Check that the seat operates back and forth smoothy and the locking portion locks properly.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
Put on gloves to protect your hands.
Remove the recliner switch (A) and height switch (B).
After loosening the mounting screw, then remove the front seat outer shield cover (A).
Disconnect the connector (A).
Install in the reverse order of removal.
Make sure the connector is plugged in properly.
Replace any damaged clips.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
Put on gloves to protect your hands.
Remove the following items.
Front seat assembly
Front seat outer shield cover
Push the lock pin (B), remove the headrest (A).
Remove the protector (A).
Disconnect the connectors (A).
Push the clips (B) from the front seat back board (A).
Push the middle area of clip using the flat head screwdriver.
Be careful not to damage the clip.
After loosening the mounting screws, then remove the air ventilation seat duct (A).
Push the protecter (A) by the seat back frame.
Remove the front seat back side protector (A).
Pull out the headrest guides (A) while pinching the end of the guides, and remove them.
Remove the front seat back cover (A) from the frame.
After removing the velcro tape (B) on the front of seat back and remove the seat back cover (A).
Install in the reverse order of removal.
Make sure the connector is plugged in properly.
Replace any damaged clips.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
Put on gloves to protect your hands.
Remove the following items.
Front seat assembly
Front seat outer shield cover
Remove the protector (A).
Disconnect the connectors (A).
Push the protecter(A), and then front seat cushion cover (C) from the frame(B).
Remove the front seat cushion cover (A) from the frame.
After removing the velcro tape (B) on the front of seat cushion and remove the seat cushion cover (A).
Install in the reverse order of removal.
Make sure the connector is plugged in properly.
Replace any damaged clips.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
Put on gloves to protect your hands.
Remove the following items.
Front seat assembly
Front seat outer shield cover
After loosening the mounting screws, then remove the front seat inner shield cover (A).
After loosening the mounting bolts, then disconnect the seat back frame (A) and seat cushion frame (B).
Tightening torque :
49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)
Install in the reverse order of removal.
Remove the side air bag for replacing side air bag installation seat.
Before service, be fully aware of precautions and service procedure relevant to air bag.
(Refer to the group RT - Airbag)
