1.
After loosening the mounting bolts, then remove the rear seat cushion (A).
Tightening torque :
34.3 ~ 53.9 N.m (3.5 ~ 5.5 kgf.m, 25.3 ~ 39.8 lb-ft)
After loosening the mounting bolts, then remove the rear seat cushion (A).
Tightening torque :
34.3 ~ 53.9 N.m (3.5 ~ 5.5 kgf.m, 25.3 ~ 39.8 lb-ft)
Disconnect the rear seat cushion warmer connector (A).
After loosening the mounting bolts, then remove the rear seat back (A).
Tightening torque :
(B) : 19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)
(C) : 9.8 ~ 13.7 N.m (1.0 ~ 1.4 kgf.m, 7.2 ~ 10.1 lb-ft)
Disconnect the rear seat folding lever cable (A).
Install in the reverse order of removal.
Make sure the connector is plugged in properly.
After loosening the mounting bolts, then remove the rear seat cushion (A).
Tightening torque :
34.3 ~ 53.9 N.m (3.5 ~ 5.5 kgf.m, 25.3 ~ 39.8 lb-ft)
Disconnect the rear seat cushion warmer connector (A).
The rear center seat belt lower anchor (A) be removed after pushing the lock pin (B) as arrow direction.
After loosening the mounting bolts, then remove the rear seat back (A).
Tightening torque :
(B) : 19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)
(C) : 9.8 ~ 13.7 N.m (1.0 ~ 1.4 kgf.m, 7.2 ~ 10.1 lb-ft)
Install in the reverse order of removal.
Make sure the connector is plugged in properly.
After loosening the mounting bolt, then remove the rear seat side back assembly (A).
Tightening torque :
34.3 ~ 53.9 N.m (3.5 ~ 5.5 kgf.m, 25.3 ~ 39.8 lb-ft)
[Sedan]
Tightening torque :
34.3 ~ 53.9 N.m (3.5 ~ 5.5 kgf.m, 25.3 ~ 39.8 lb-ft)
Disconnect the airbag connector (A).
Install in the reverse order of removal.
Make sure the connector is plugged in properly.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
Put on gloves to protect your hands.
Remove the following items.
Rear seat cushion assembly
Rear seat back assembly [LH]
Push the lock pin (B) and then remove the headrest (A).
After loosening the mounting screw, then reomve the rear seat upper bezel (A).
Disconnect the rear seat back cover protector (A).
Disconnect the rear seat back upper protector (A).
Pull out the headrest guides (A) while pinching the end of the guides, and remove them.
Remove the rear seat back cover (A) from the rear seat back frame (B).
After removing the velcro tape (B) on the rear of seat back and remove the seat back cover (A).
Install in the reverse order of removal.
Make sure the connector is plugged in properly.
Replace any damaged clips.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
Put on gloves to protect your hands.
Remove the following items.
Rear seat cushion assembly
Rear seat back assembly [LH]
Rear seat back cover [LH]
After loosening the mounting bolts, then remove the rear seat latch assembly (A).
Disconnect the rear seat latch rod (B).
Tightening torque :
19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)
Install in the reverse order of removal.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
Put on gloves to protect your hands.
Remove the following items.
Rear seat cushion assembly
Rear seat back assembly [RH]
Push the lock pin (B) and then remove the headrest (A).
Using a long nose, remove the rock pin (B) and rear seat armrest (A).
After loosening the mounting screws, then remove the rear seat armrest back panel (A).
After loosening the mounting screw, then reomve the rear seat upper bezel (A).
Remove the rear center seat belt cover (A).
Disconnect the rear seat back cover protector (A).
Disconnect the rear seat back upper protector (A).
Pull out the headrest guides (A) while pinching the end of the guides, and remove them.
Remove the rear seat back cover (A) from the rear seat back frame (B).
After removing the velcro tape (B) on the rear of seat back and remove the seat back cover (A).
Install in the reverse order of removal.
Make sure the connector is plugged in properly.
Replace any damaged clips.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
Put on gloves to protect your hands.
Remove the following items.
Rear seat cushion assembly
Rear seat back assembly [RH]
Rear seat back cover [RH]
After loosening the mounting bolts, then remove the rear seat latch assembly (A).
Disconnect the rear seat latch rod (B).
Tightening torque :
19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)
Install in the reverse order of removal.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
Put on gloves to protect your hands.
Using a long nose, remove the rock pin (B) and rear seat armrest (A).
Install in the reverse order of removal.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
Put on gloves to protect your hands.
Remove the following items.
Rear seat cushion assembly
Disconnect the connectors (A)
Remove the hog-ring clips (A).
After removing the hog-ring clips (B) on the rear of seat cushion and remove the rear seat cushion cover (A).
Install in the reverse order of removal.
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
Replace the hog ring clips with new ones using special tool [C (09880-4F000)].
