2.
Remove the ground line after removing the bolt (A).
Remove the following items;
Engine cover.
Air cleaner assembly and air duct. (Refer to "Intake and Exhaust system" in EM group.)
Battery and battery tray.
(Refer to "Charging system" in EE group.)
Remove the ground line after removing the bolt (A).
Disconnect the solenoid valve connector (A) and inhibitor switch connector (B).
Remove the control cable (C) after removing the nut (A) and the bolt (B).
Tightening torque:
(A) 9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)
(B) 14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)
Remove the solenoid valve connector and inhibitor switch connector wiring mounting bracket (A).
Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).
Remove the wiring mounting bolts (A).
Remove the automatic transaxle upper mounting bolt (A-2ea) and the starter motor mounting bolt (B-2ea).
Tightening torque:
(A),(B): 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
Remove the mounting cover.
Remove the support bracket mounting bolts (A).
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.8 lb-ft)
After assembling the T-shaped beam, install the supporter (SST No:09200-2S200) to the beam of SST(09200-38001,09200-3N000).
Install the adaptor (SST No:09200-2S100) to the beam of (SST No:09200-38001, 09200-3N000).
Install the assembled SST (A) on the engine room.
Hang the ring (B) on the engine hanger, support the engine.
To prevent slip, the support supports the body securely.
Remove the automatic transaxle mounting support bracket (C).
Tightening torque:
(A) 78.5 ~ 98.1 N.m (8.0 ~ 10.0 kgf.m, 57.9 ~ 72.3 lb-ft)
(B) 58.9 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)
Lift the vehicle with a jack.
Remove the under cover (A).
Tightening torque:
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)
Remove the side cover (A).
Remove the following items;
Sub frame assembly.
(Refer to "Front suspension system" in SS group.)
Drive shaft assembly.
(Refer to "Drive shaft assembly " in DS group.)
Remove the CKP sensor (A) by removing a bolt.
Remove the dust cover (A) by removing the bolts (2ea).
Remove the intercooler pipe (A).
Remove the torque converter mounting bolt (A-4ea) with rotating the crankshaft.
Tightening torque:
45.1 ~ 52.0 N.m (4.6 ~ 5.3 kgf.m, 33.3 ~ 38.3 lb-ft)
Remove the automatic transaxle with a jack after removing the mounting bolt (A-3ea, B-2ea).
Tightening torque:
[A] 35.0 ~ 50.0 N.m (3.5 ~ 5.0 kgf.m, 25.3 ~ 36.2 lb-ft)
[B] 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
