Installation
note
●

Thoroughly clean all parts to be assembled.

●

Always use a new cylinder head and manifold gasket.

●

Always use a new cylinder head bolt.

●

The cylinder head gasket is a metal gasket. Take care not to bend it.

●

Rotate the crankshaft, set the No.1 piston at TDC.

1.

Cylinder head dowel pins must be aligned.

2.

Select the cylinder head gasket.

(1)

Measure the piston protrusion from the upper cylinder block face (I) on 8 places (A ~ H) at T.D.C.

Measure on the crankshaft center line considering the piston migration.

(2)

Select the gasket in the table below using the average value of piston protrusions. Although even the only 1 point is over than the each rank limit, use 1 rank upper gasket than specified in the table below.

Displacement

1.7

Average of piston protrusion

0.035 ~ 0.105mm

(0.0014 ~ 0.0041in)

0.105 ~ 0.175mm

(0.0041 ~ 0.0069in)

0.175 ~ 0.245mm

(0.0069 ~ 0.0096in)

Gasket thickness

1.00 ~ 1.15mm

(0.0394 ~ 0.0453in)

1.05 ~ 1.20mm

(0.0413 ~ 0.0472in)

1.10 ~ 1.25mm

(0.0433 ~ 0.0492in)

Limit of each rank extent

0.14mm (0.0055in)

0.21mm (0.0083in)

-

Identification code

Gasket grade

A

B

C

(3)

Install the gasket so that the identification mark faces toward the timing chain side.

3.

Install the cylinder head gasket (A) on the cylinder block.

note

Be careful of the installation direction.

4.

Place the cylinder head (A) quietly in order not to damage the gasket with the bottom part of the end.

5.

Install the cylinder head bolts.

(1)

Do not apply engine oil on the cylinder head bolts.

(2)

Using the SST (09221-4A000), install and tighten the 10 cylinder head bolts, in several passes, in the sequence shown.

Tightening torque :

47.1~51.0Nm (4.8~5.2kgf.m, 34.7~37.6lb-ft) + (88~92°) + (118~122°)

note

Do not reuse the cylinder head bolts.

6.

Istall the HLA (Hydraulic Lash Adjust) (A).

(1)

Until installing HLA shall be held upright so that diesel oil in HLA should not spill and assured that dust does not adhere to HLA.

(2)

HLA shall be inserted tenderly to the cylinder head not to spill diesel oil from HLA. In case of spilling, air bent shall be done in accordance with the air bent procedure.

note

Stroke HLA in diesel oil 4~5 times by pushing its cap while pushing the ball down slightly by hard steel wire. (Take care not to severely push hard steel wire down since ball is several grames.)

7.

Install the cam follower (A).

8.

Install the camshaft (A).

9.

Install the camshaft bearing caps (A).

Tightening torque :

12.7 ~ 14.7N.m (1.3 ~ 1.5kgf.m, 9.4 ~ 10.8lb-ft)

10.

Install the vacuum pump (A) with new gasket (B).

Tightening torque :

10.8 ~ 14.7N.m (1.1 ~ 1.5kgf.m, 8.0 ~ 10.8lb-ft)

note

Apply engine oil to the O-ring(A) of vacuum pump shaft before assembling vacuum pump.

11.

Install the thermostat housing (A).

Tightening torque :

9.8 ~ 11.8N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7lb-ft)

12.

Reconnect the water hose (A) to thermostat housing.

13.

Install the glow plug (A) and glow plug plate.

Tightening torque :

Glow plug : 14.7 ~ 19.6N.m (1.5 ~ 2.0kgf.m, 10.8 ~ 14.5lb-ft)

Plate nut : 0.8~1.5N.m (0.08 ~ 0.15kgf.m, 0.6 ~ 1.1lb-ft)

14.

Install the common rail (A).

Tightening torque :

14.7 ~ 21.6N.m (1.5 ~ 2.2kgf.m, 10.8 ~ 15.9lb-ft)

15.

Install the intake and exhaust manifold. (Refer to Intake and exhaust system in this group)

16.

Install the timing chain. (Refer to Timing chain in this group)

17.

Install the engine assembly to the vehicle. (Refer to Engine and transaxle assembly in this group)

Яндекс.Метрика