1.
Using a screwdriver or remover, remove the rear door delta inner cover (A).
Take care not to scratch the door trim and other parts.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the rear door delta inner cover (A).
Using a screwdriver or remover, remove the rear door grip handle cover (B).
After loosening the mounting screws, then remove the rear door trim (A).
Remove the inside handle cable (A).
Disconnect the seat heater switch connector (A) and power window switch connector (B).
Install in the reverse order of removal.
Make sure connectors are connected properly and each rod is connected securely.
Make sure the door lock and opens properly.
Replace any damaged clips.
Remove the rear door trim.
After loosening the rear door inside handle mounting screws, then remove the rear door inside handle (A).
Install in the reverse order of removal.
Replace any damaged clips.
Make sure the door lock and opens properly.
Put on gloves to protect your hands.
Remove the rear door trim.
Remove the rear door belt inside weatherstrip (A).
Loosen the rear door delta lower run & channel mounting bolts and nut.
Tightening torque :
3.9 ~ 5.9 N.m (0.4 ~ 0.6 kgf.m, 2.9 ~ 4.3 lb-ft)
After loosening the mounting screws, then remove the rear door belt outer weatherstrip (A).
Using a screwdriver or remover, remove the rear door rear frame garnish (A).
Rear door rear frame garnish needs to be changed to insure product quality.
Remove the glass mounting hole plug (B).
Use the door switch to align the mounting hole/bolt with the hole in the door.
If unable to operate the window motor, remove the motor and align the hole by hand.
Be careful not to drop the glass and/or scratch the glass surface.
Carefully adjust the glass (A) until you can see the bolts, then loosen them. Separate the glass from the glass run and carefully pull the glass out through the window slot.
Tightening torque :
3.9 ~ 11.8 N.m (0.4 ~ 1.2 kgf.m, 2.9 ~ 8.7 lb-ft)
Installation is the reverse the removal.
Roll the glass up down to see if it move freely without binding
Adjust the position of the glass as needed.
Make sure the door lock and opens properly.
Replace any damaged clips
Remove the rear door trim.
Disconnect the speaker connector (B).
After loosening the mounting screws, then remove the speaker (A).
Install in the reverse order of removal.
Use sheet metal screws to secure the speaker.
Make sure the connector are connected properly and each rod is connected securely.
Make sure the door lock and opens properly.
Replace any damaged clips.
Remove the rear door trim.
Disconnect the power window motor connector (B).
After loosening the mounting screws, then remove the power window motor (A).
Install in the reverse order of removal.
The area of rotational parts and springs should be applied with sufficient grease.
Roll the glass up down to see if it move freely without binding.
Remove the hole plug (B).
After loosening the mounting bolt, then remove the outside handle cover (A).
Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Remove the outside handle (A) by sliding it rearward.
Install in the reverse order of removal.
Make sure the door lock and open properly.
Remove the following parts.
Rear door trim
Window glass
Outside handle
Loosen the mounting screw (A).
Loosen the door latch (B) mounting screws.
After loosening the rear door module mounting bolts, then remove the rear door module (A).
Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Remove the wiring clip (A).
Remove the rear door delta lower run & channel (A).
Disconnect the connectors and rear door module wiring harness (A).
Install in the reverse order of removal.
The area of whole parts should be applied with sufficient grease.
Make sure the connector is plugged in properly and each rod is connected securely.
Make sure the door lock and open properly.
Remove the following items :
Rear door trim
Window glass
Outside handle
Loosen the mounting screw (A).
Loosen the door latch (B) mounting screws.
After loosening the rear door module mounting bolts, then remove the rear door module (A).
Tightening torque :
6.9 ~ 10.8N.m (0.7 ~ 1.1kgf.m, 5.1 ~ 8.0 lb-ft)
Remove the wiring clip (A).
Remove the rear door delta lower run & channel (A).
Disconnect the rear latch connector (A).
Remove the rear door latch (A).
Install in the reverse order of removal.
Make sure the connector is connected properly.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Detach the clips, then remove the rear door side weatherstrip (A).
Installation is the reverse the removal.
Replace any damaged clips.
