1.
Using a screwdriver or remover, remove the front door quadrant inner cover (A).
Take care not to scratch the door trim and other parts.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the front door quadrant inner cover (A).
Using a screwdriver or remover, remove the front door grip handle cover (B).
After loosening the mounting screws, then remove the front door trim (A).
Remove the inside handle cable (A).
Disconnect the midrange speaker connector (A), IMS switch connector (B), outside rear view mirror switch connector (C), door lamp connector (D).
Install in the reverse order of removal.
Make sure of connectors is plugged in properly and each rod is connected securely.
Make sure the door lock and opens properly.
Replace any damaged clips.
Remove the front door trim.
After loosening the front door inside handle mounting screws, then remove the front door inside handle (A).
Install in the reverse order of removal.
Replace any damaged clips.
Make sure the door lock and opens properly.
Remove the front door trim.
Remove the front door belt inside weatherstrip (A).
Remove the glass mounting hole plug (B).
Take care not to drop to glass and scratch the glass surface.
Carefully move the glass (A) until you can see the bolts, then loosen them. Separate the glass from the glass run and carefully pull the glass out through the window slot.
Tightening torque :
3.9 ~ 11.8 N.m (0.4 ~ 1.2 kgf.m, 2.9 ~ 8.7 lb-ft)
Install in the reverse order of removal.
Roll the glass up down to see if it move freely without binding.
Adjust the position of the glass as necessary.
Remove the front door trim.
Disconnect the speaker connector (B).
After loosening the mounting screws, then remove the speaker (A).
Install in the reverse order of removal.
Use sheet metal screws to secure the speaker.
Make sure the connector are connected properly and each rod is connected securely.
Make sure the door lock and opens properly.
Replace any damaged clips.
Remove the front door trim.
Disconnect the power window motor connector (B).
After loosening the mounting bolts, then remove the power window motor (A).
Install in the reverse order of removal.
The area of rotational parts and springs should be applied with sufficient grease.
Roll the glass up down to see if it move freely without binding.
Replace any damaged clips.
Make sure the door lock and opens properly.
Remove the following parts.
Front door trim.
Window glass.
Outside handle.
Loosen the mounting screw (A).
Disconnect the outside rear view mirror connector (A).
Loosen the door latch (B) mounting screws.
After loosening the mounting bolts, then remove the front door module (A).
Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Disconnect the connectors and front door module wiring harness (A).
Install in the reverse order of removal.
The area of whole parts should be applied with sufficient grease.
Make sure the connector is plugged in properly and each rod is connected securely.
Make sure the door lock and open properly.
Replace any damaged clips.
Remove the hole plug (B).
After loosening the mounting bolt, then remove the outside handle cover (A).
Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Remove the outside handle (A) by sliding it rearward.
Disconnect the outside handle connector (A).
Installation is the reverse the removal.
Make sure the door lock and open properly.
Remove the following items :
Front door trim
Window glass
Outside handle
Loosen the mounting screw (A).
Disconnect the outside rear view mirror connector (A).
Loosen the door latch (B) mounting screws.
After loosening the front door module mounting bolts, then remove the front door module (A).
Tightening torque :
6.9 ~ 10.8N.m (0.7 ~ 1.1kgf.m, 5.1 ~ 8.0 lb-ft)
Disconnect the wiring harness (B) and latch connector (A).
Remove the front door latch (A).
Install in the reverse order of removal.
Make sure the connector is connected properly.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Detach the clips, then remove the front door side weatherstrip(A).
Install in the reverse order of removal.
Replace any damaged clips.
Check the glass run channel for damage or deterioration, and replace them necessary.
Remove the front door trim.
Remove the glass mounting hole plug (B).
Carefully move the glass (A) until you can see the glass mounting bolts, then loosen them.
Check that the glass moves smoothly.
Make sure the door latches securely without slamming it. If necessary adjust the striker (A): The striker nuts are fixed. The striker can be adjusted up or down, and in or out.
Loosen the screws (B) just enough for the striker to move.
Tightening torque:
(B): 16.7 ~ 21.6 N.m (1.7 ~ 2.2 kgf.m, 12.3 ~ 15.9 lb-ft)
Tap on the striker with a plastic hammer to adjust the striker. The striker will not move much, but will give some adjustment.
Hold the outer handle out, and push the door against the body to be sure the striker allows a flush fit. If the door latches properly, tighten the screws and recheck.
After installing the door, check for a flush fit with the Body, then check for equal gaps between the front, rear, and bottom, door edges and the body. Check that the door and body edges are parallel. Before adjusting, replace the mounting bolts.
Check that the door and body edges are parallel.
[Wagon]
[Sedan]
Place the vehicle on a firm, level surface when adjusting the doors.
Adjust at the hinges (A) :
Loosen the door mounting bolts slightly, and move the door in or out until it aligns flush with the body.
Loosen the hinge mounting bolts slightly, and move the door backward or forward, up or down as necessary to equalize the gaps.
Place a shop towel on the jack to prevent damage to the door when adjusting the door.
Tightening torque :
(B) : 21.6 ~ 26.5 N.m (2.2 ~ 2.7 kgf.m, 15.9 ~ 19.5 lb-ft)
(C) : 33.3 ~ 41.2 N.m (3.4 ~ 4.2 kgf.m, 24.6 ~ 30.4 lb-ft)
Grease the pivot portions of the hinges indicated.
Check for water leaks.
