DESCRIPTION
BURGLAR ALARM SYSTEM

The burglar alarm system is armed automatically after the doors, hood, and tailgate are closed and locked.

The system is set off when any of these things occur :

A door is forced open.

The tailgate is opened.

The hood is opened.

When the system is set off, the alarm sounds and the hazard lamp flash for about 30 seconds or until the system is disarmed by unlocking the transmitter or door key.

For the system to arm, the ignition switch must be off and the key removed. Then, the body control module must receive signals that the doors, hood, and tailgate are closed and locked. When everything is closed and locked, none of the control unit inputs are grounded.

The door switches, hood switch and tailgate switch are all close and lock the doors with the remote transmitter and then the system arms immediately.

If anything is opened after the system is armed, the body control module gets a ground signal from that switch, and the system is set off.

If one of the switches is misadjusted or there is a short in the system, the system will not arm. As long as the body control module continues to get a ground signal, it thinks the vehicle is not closed and locked and will not arm.

KEYLESS ENTRY SYSTEM

The burglar alarm system is integrated with the keyless entry system. The keyless entry system allows you to lock and unlock the vehicle with the remote transmitter. When you push the LOCK button, all doors lock. When you push the UNLOCK button again, all doors unlock.

The room lamp, if its switch is in the center position, will come on when you press the UNLOCK button. If you do not open a door, the light will go off in about 30 seconds, the doors will automatically relock, and the burglar alarm system will rearm. If you relock the doors with the remote transmitter within 30 seconds, the light will go off immediately.

You cannot lock or unlock the doors with the remote transmitter if the key is in the ignition switch.

The system will signal you when the doors lock and unlock by flashing the hazard lamp once when they lock, and twice when they unlock.

FUNCTION
KEYLESS ENTRY FUNCTION

DOOR LOCK / UNLOCK and Tailgate (Folding key only) operation are performed with remocon

1.

Keyless entry function is performed in a state that key in SW is eliminated from key cylinder

2.

LOCK / UNLOCK and tailgate signals are received from the transmitter and DOOR LOCK / UNLOCK and Tailgate signals are output.

TRANSMITTER(TX) SPEC
1.

Transmission Distance : 30m or more from outside of the car

2.

Registration procedure of the transmitter

(1)

In registration mode, it shall be possible to register up to Max 4EA.

(2)

At re-registration, data are registered newly after deleting the previous TX DATA

No.

Saved CODE

CODE to change

Changed CODE

1

-

A

A

2

A

B

B (A is deleted)

3

B

C, D

C, D (B is deleted)

4

C, D

E, F, G

E, F, G (C, D is deleted)

5

E, F, G

H, I, J, K

H, I, J, K (E, F, G are deleted)

6

A, B

C, F, E, F, G

C, F, E, F

7

A, B

C, C, D, E, F

C, D, E, F

8

A, B, C, D

A

A

9

A, B, C, D

E

E

(3)

For the registration procedures by using Hi-scan tool, refer to "TRANSMITTER CODE REGISTRATION".

3.

Transmitter signal & Receiver Spec

(1)

Transmission signal

A.

Transmit relevant transmission DATA (Transmission frame) twice by pushing TX SW.

B.

Only LOCK signal is output when pushing TX LOCK SW and UNLOCK SW at the same time.

DISARM
Condition 1

State

Description

Initial Condition

ALARM state

Event

IGN KEY ON during 30sec or ALT"L" = ON

TX(Transmitter) Unlock & Any Door open(4Door SW ON)

TX(Transmitter) Lock & Lock confirm failed

Driver door key unlock switch ON.

Driver door key lock SW ON & Lock confirm failed

TX tailgate ON (Folding key type only : 3 button).

Action

The state goes to DISARM state

Hazard relay off, Horn relay off and start inhibit relay off.

TX Unlock

-

Unlock relay on for 0.5 sec.

-

Hazard relay on (TWICE)

Condition 2

State

Description

Initial Condition

DISARM state & (IGN KEY OUT) & Any Door open

Event

TX Unlock

Action

No state change

TX UNLOCK

-

Unlock relay on for 0.5 sec

-

Hazard relay on (Twice)

Condition 3

State

Description

Initial Condition

ARMWAIT state

Event

At least one entrance opened

Any door is unlocked

Key in SW ON

Driver door key unlock SW ON

Action

The state goes to DISARM state

Condition 4

State

Description

Initial Condition

AUTOLOCKTIMER1 state

Event

At least one entrance opened

Key in SW ON

Lock by AUTOLOCK, but Lock confirmation failure

Tx Lock, but Lock confirmation failure

Driver door key unlock SW ON, but Lock confirmation failure

Action

The state goes to DISARM state

Condition 5

State

Description

Initial Condition

AUTOLOCKTIMER2 state

Event

Any Door open

Key in SW ON

Lock by AUTOLOCK, but Lock confirmation failure

Tx Lock, but Lock confirmation failure

Driver door key lock SW ON, but Lock confirmation failure

Action

The state goes to DISARM state

Condition 6

State

Description

Initial Condition

ARM state

Event

IGN KEY ON

Driver door key unlock SW ON

Action

The state goes to DISARM state

Condition 7

State

Description

Initial Condition

REARM state

Event

IGN KEY ON during 30sec or ALT"L" = ON

Tx Lock, but Lock confirmation failure

Driver door key unlock SW ON

Driver door key lock SW ON & Lock confirmation failure

TX tailgate ON (Folding key type only : 3 button).

Action

The state goes to DISARM state

Start Inhibit relay OFF

Condition 8

State

Description

Initial Condition

PREARM state

Event

Key in SW ON

All entrance closed & Any Door is unlocked

Any Door open & Tx Unlock

Action

The state goes to DISARM state

TX UNLOCK

-

Unlock relay on for 0.5sec

-

Hazard relay on (Twice)

Condition 9

State

Description

Initial Condition

AutoLockTimer3 state

Event

Key in SW ON

Hood open

Any Door open

Lock confirm failed

Action

The state goes to DISARM state

ARM
-

LED is Blinking

Condition 1

State

Description

Initial Condition

ARM state

Event

Tx Lock

Action

No state change

Hazard relay 1Time on(1sec)

Condition 2

State

Description

Initial Condition

ARMWAIT state

Event

ARMWAITTIMER is expired

Action

The state goes to ARM state

ALARM
-

LED is Blinking

Condition 1

State

Description

Initial Condition

ARM state

Event

Any entrance open (DOORS, TAILGATE, or HOOD)

Action

The state goes to ALARM state

The horn is ON one time for 27sec(±2sec)

The hazard is driven also (During Horn driving)

Engine Start Inhibit is ON

T1 : 27s ± 2sec, T2 : 0.5s ± 0.1sec.

note

Horn Output : Period : 1sec(Can be calibrated Horn Period), 50% Duty

Condition 2

State

Description

Initial Condition

REARM state

Event

Any door open or Hood open or tailgate open

Action

The state goes to ALARM state

The horn is ON one time for 27sec (±2sec.)

The hazard is driven also (During horn driven)

ARM WAIT MODE
-

LED is turn on

Condition 1

State

Description

Initial Condition

ARMWAIT state

Event

Tx Lock

Action

The state goes to State

TX LOCK

-

Hazard relay 1 Time on(1sec)

Condition 2

State

Description

Initial Condition

DISARM state & IGN KEY OUT & All entrances closed (DOORS, HOOD and TAILGATE)

Event

Tx Lock & locked confirmed

Driver door key lock SW ON & Locked confirmed

Action

The state goes to ARMWAIT State

Start ARMWAITTIMER

TX LOCK & locked confirmed.

-

Hazard relay 1 Time on (1 sec.)

Condition 3

State

Description

Initial Condition

ALARM state & All entrances closed(DOORS, HOOD and TAILGATE)

Event

Tx Lock & locked confirmed

Driver door key lock SW ON & Locked confirmed

Action

The state goes to ARMWAIT state

Start ARMWAITTIMER

Horn relay off

Start inhibit relay off

Hazard relay 1Time on(1sec)

Condition 4

State

Description

Initial Condition

AUTOLOCKTIMER1 state

Event

AUTO LOCK confirmed

Tx Lock & locked confirmed

Driver door key lock SW ON & Locked confirmed

Action

The state goes to ARMWAIT state

Start ARMWAITTIMER

Hazard relay 1Time on(1sec)

Condition 5

State

Description

Initial Condition

PREARM state

Event

Hood and 4door are closed & All doors locked & Tailgate closed.

Action

The state goes to ARMWAIT state

Start ARMWAITTIMER

Hazard relay 1Time on(1sec)

Dead lock

Tailgate mark = set

Condition 6

State

Description

Initial Condition

REARM state

Event

Tx Lock & locked confirmed

Drive door key lock SW ON & locked confirmed

Action

The state goes to ARMWAIT state

Start ARMWAITTIMER

Start inhibit relay off

Hazard relay 1Time on(1sec)

Condition 7

State

Description

Initial Condition

Auto Lock Timer3 state

Event

Tx Lock & locked confirmed

Drive door key lock SW ON & locked confirmed

Action

The state goes to ARMWAIT state

Start ARMWAITTIMER

Start inhibit relay off

Hazard relay 1Time on(1sec)

REARM MODE
-

LED is Blinking

Condition 1

State

Description

Initial Condition

ALARM state

Event

All entrance is closed & Alarm Patten finished

Action

The state goes to REARM state

AUTOLOCKTIMER1 MODE
-

LED is Blinking

Condition 1

State

Description

Initial Condition

ARM state

Event

Tx Unlock

Action

The state goes to AUTOLOCKTIMER1 state

Start AUTOLOCKTIMER1

Hazard relay Twice on(0.5s ON/0.5s OFF)

Condition 2

State

Description

Initial Condition

AUTOLOCKTIMER1 state

Event

Timer is expired

Tx Unlock

Action

The state goes to State

Tx Unlock

-

Hazard relay Twice on(0.5s ON/0.5s OFF)

-

Restart AUTOLOCKTIMER1

Expire AUTOLOCKTIMER1

-

AUTOLOCK

Condition 3

State

Description

Initial Condition

ARMWAIT state

Event

Tx Unlock

Action

The state goes to AUTOLOCKTIMER1 state

Start AUTOLOCKTIMER1

Hazard relay Twice on(0.5s ON/0.5s OFF)

Condition 4

State

Description

Initial Condition

DISARM state & All entrances closed (DOORS, HOOD & TAILGATE) & IGN KEY OUT

Event

Tx Unlock

Action

The state goes to AUTOLOCKTIMER1 state

Start AUTOLOCKTIMER1

Hazard relay Twice on(0.5s ON/0.5s OFF)

Condition 5

State

Description

Initial Condition

ALARM state & All entrances are closed (DOORS, HOOD & TAILGATE)

Event

Tx Unlock

Action

The state goes to AUTOLOCKTIMER1 state

Start AUTOLOCKTIMER1

Hazard relay Twice on(0.5s ON/0.5s OFF)

Start inhibit relay off

Horn relay off

Condition 6

State

Description

Initial Condition

REARM state

Event

Tx Unlock

Action

The state goes to AUTOLOCKTIMER1 state

Start AUTOLOCKTIMER1

Hazard relay Twice on(0.5s ON/0.5s OFF)

Start inhibit relay off

Condition 7

State

Description

Initial Condition

Auto Lock Timer3 state

Event

Tx Unlock

Action

The state goes to AUTOLOCKTIMER1 state

Start AUTOLOCKTIMER1

Hazard relay Twice on(0.5s ON/0.5s OFF)

AUTOLOCKTIMER2 MODE
-

LED is blinking

Condition 1

State

Description

Initial Condition

AUTOLOCKTIMER2 state

Event

Timer is expired

Tx Unlock

Action

No State change

Tx Unlock

-

Hazard relay Twice on(0.5s ON/0.5s OFF)

-

The timer restart

Expire AUTOLOCKTIMER2

-

AUTOLOCK

Condition 2

State

Description

Initial Condition

DISARM state & All Doors are closed & (HOOD is opened) & IGN KEY OUT

Event

Tx Unlock

Action

The state goes to AUTOLOCKTIMER2 state

Start AUTOLOCKTIMER2

Hazard relay Twice on(0.5s ON/0.5s OFF)

Condition 3

State

Description

Initial Condition

ALARM state & All Door are closed & (HOOD is opened)

Event

Tx Unlock

Action

The state goes to AUTOLOCKTIMER2 state

Start AUTOLOCKTIMER2

Hazard relay Twice on(0.5s ON/0.5s OFF)

Start inhibit relay off

Horn relay off

Condition 4

State

Description

Initial Condition

PREARM state

All Doors are closed & (HOOD is opened)

Event

Tx Unlock

Action

The state goes to AUTOLOCKTIMER2 state

Start AUTOLOCKTIMER2

Memorize Hood and Tailgate state

Hazard relay Twice on(0.5s ON/0.5s OFF)

AUTO LOCK TIMER3 MODE

- LED is blinking

Condition 1

State

Description

Initial Condition

ARM state

Event

Tx TAILGATE Unlock

Action

The state goes to AUTO LOCK RELAY TIMER3 state

Start AUTO LOCK RELAY TIMER3

Hazard relay Twice on(0.5s ON/0.5s OFF)

TAILGATE Mark=set

Dead unlock

Condition 2

State

Description

Initial Condition

AutoLockTimer3 state

Event

Tx TAILGATE Unlock

Action

Restart AUTO LOCK TIMER3 state

Condition 3

State

Description

Initial Condition

ARMWAIT state

Event

Tx TAILGATE Unlock

Action

The state goes to AUTO LOCK RELAY TIMER3 state

Start AUTO LOCK RELAY TIMER3

Dead Unlock

Hazard relay Twice on(0.5s ON/0.5s OFF)

TAILGATE Mark=set

PREARM MODE
-

LED is blinking

Condition 1

State

Description

Initial Condition

AUTOLOCKTIMER2 state

Event

AUTOLOCK confirmed

Tx Lock & locked confirmed

Driver door key lock SW ON & Locked confirmed

Action

The state goes to PREARM state

Condition 2

State

Description

Initial Condition

DISARM state & IGN KEY OUT

Event

((4Door Not Closed = ON & Tailgate SW = OFF or (Hood SW = ON)) & Tx Lock & Locked confirmed

((4Door Not Closed = ON & Tailgate SW = OFF or (Hood SW = ON)) & driver door key lock SW ON on & Locked confirmed

Action

The state goes to PREARM state

Condition 3

State

Description

Initial Condition

ALARM state & Hood SW = ON

Event

Tx Lock & Locked confirmed

Driver door key lock SW ON & Locked confirmed

Action

The state goes to PREARM state

Start inhibit relay off

Horn relay off

Hazard relay 1Time on (1sec.)

Condition 4

State

Description

Initial Condition

AUTOLOCKTIMER3 state

Event

Expire Auto Lock Timer3

Tailgate open

Action

The state goes to PREARM state.

RESET
1.

In case of taking the battery out during the ALARM state

Condition 1

State

Description

Initial Condition

During ALARM, REARM

Event

TAKING THE BATTERY OUT (Cold or Warm RESET)

Action

The state goes to ALARM mode

Horn relay 1 Times on (No remained time of warning signal)

Hazard lamp is flashing during making horn

2.

In case of taking the battery out during arm

Condition 2

State

Description

Initial Condition

ARM state

Event

TAKING THE BATTERY OUT (Cold or Warm RESET)

Action

The state goes to ARM mode

Maintained ARM state

The RESTRICTED FUNCTION OF UNLOCK BY CENTROL DOOR LOCK SW
1.

In IGN Key OUT, UNLOCK is restricted by Central Door Lock SW if All DR LOCK & CLOSED when TX LOCK.

2.

In IGN Key OUT, UNLOCK is restricted by Central Door Lock SW if All DR LOCK & CLOSED when DR LOCK by DRV DR Key.

3.

The restricted function of UNLOCK is canceled when TX UNLOCK signal output during the restricted function of Central Door Lock SW.

4.

The restricted function of UNLOCK is canceled when DR UNLOCK signal output during the restricted function of Central Door Lock SW.

T1 : 0.5s ± 0.1s

TAILGATE RELEASE FUNCTION
PERMISSIVE MODE STATE

State

Description

Initial Condition

PROHIBITIONAL MODE STATE

Event

Any Door Unlocked

Operating

MOVE TO PERMISSIVE MODE STATE

State

Description

Initial Condition

30s PERMISSIVE MODE STATE

Event

Any Door Unlocked

Operating

MOVE TO PERMISSIVE MODE STATE

State

Description

Initial Condition

PERMISSIVE MODE STATE

Event

TAILGATE RELEASE SW = ON

Operating

TAILGATE RELEASE RELAY 0.5SEC ON

MOVE TO PERMISSIVE MODE STATE

30s PERMISSIVE MODE STATE

State

Description

Initial Condition

PROHIBITIONAL MODE STATE

Event

TAILGATE UNLOCK

Operating

START TAILGATE TIMER

HAZARD 2 FLASHING

MOVE TO 30s PERMISSIVE MODE STATE

State

Description

Initial Condition

30s PERMISSIVE MODE STATE

Event

TAILGATE UNLOCK

Operating

RESTART TGATE TIMER

HAZARD 2 times FLASHING

MOVE TO 30s PERMISSIVE MODE STATE

State

Description

Initial Condition

30s PERMISSIVE MODE STATE

Event

TAILGATE RELEASE SW = ON

Operating

TAILGATE RELEASE RELAY OUTPUT FOR 0.5s

MOVE TO 30s PERMISSIVE MODE STATE

PROHIBITIONAL MODE STATE

State

Description

Initial Condition

30s PERMISSIVE MODE STATE

Event

TAILGATE OPEN→CLOSE

4Door Lock Confirm

Operating

MOVE TO PROHIBITIONAL MODE STATE

State

Description

Initial Condition

30s PERMISSIVE MODE STATE

Event

TAILGATE TIMER IS EXPIRED

Operating

MOVE TO PROHIBITIONAL MODE STATE

State

Description

Initial Condition

PERMISSIVE MODE STATE

Event

4Door Lock Confirm

Operating

MOVE TO PROHIBITIONAL MODE STATE

Яндекс.Метрика