The value of the input shaft speed should be equal to the value of the output shaft speed, when multiplied by the 2nd gear ratio, while the transaxle is engaged in the 2nd gear. For example, if the output speed is 1000 rpm and the 2nd gear ratio is 1.529, then the input speed is 1,592 rpm.
DTC DESCRIPTION
This code is set if the value of input shaft speed is not equal to the value of the output shaft, when multiplied by the 2nd gear ratio, while the transaxle is engaged in 2nd gear. This malfunction is mainly caused by mechanical troubles such as control valve sticking or solenoid valve malfunctioning rather than an electrical issue.
DTC DETECTING CONDITION
Item
Detecting Condition
Possible cause
DTC Strategy
●
2nd gear incorrect ratio
●
Faulty input speed sensor
●
Faulty output speed sensor
●
Faulty UD clutch or 2-4 brake
Enable Conditions
●
Engine speed ＞450rpm
●
Output speed ＞500rpm
●
Lever position : D,3,2
●
Input speed ＞0rpm
●
A/T oil temp output ≥ -10°C(14°F)
●
11V ≤ Battery Voltage ≤16V
●
TRANSAXLE RANGE SWITCH is normal and after 2sec is passed from IG ON
Threshold value
●
ㅣInput speed/2nd gear ratio - output speedㅣ≥200rpm
Diagnostic Time
●
More than 1sec
Fail Safe
●
Locked into 3rd gear.(If diagnosis code P0732 is output four times, the transaxle is locked into 3rd gear)
Signal Waveform
MONITOR SCANTOOL DATA
1.
Connect scan tool to data link connector(DLC).
2.
Engine "ON".
3.
Monitor the "ENGINE SPEED, INPUT SPEED SENSOR, OUTPUT SPEED SENSOR, GEAR POSITION" parameter on the scan tool.
4.
Perform the "STALL TEST" with gear position "2".
Specification : 2000~2700 engine rpm
※ This test is possible only for "HOLD S/W" or "SPORTS MODE" applied vehicles.
OPERATING ELEMENT OF EACH SHIFTING RANGE
UD/C
OD/C
REV/C
2-4/B
LR/B
OWC
P
●
R
●
●
N
●
D1
●
●
D2
●
●
D3
●
●
D4
●
●
L
●
●
●
Stall test procedure in D2 and reason
Procedure
A.
Warm up the engine.
B.
After positioning the select lever in "D" or "ON" of the HOLD SW ( Operate UP SHIFT in case of "SPORTS MODE"),depress the foot brake pedal fully after that, depress the accelerator pedal to the maximum.
* The slippage of 2ND BRAKE can be detected by stall test in D2.
Reason for stall test
A.
If there is no mechanical defaults in A/T, every slippage occur in torque converter.
B.
Therefore, engine revolution is output, but input and output speed revolution must be "zero" due to wheel's lock.
C.
If 2nd brake system(2nd gear operating part) has faults, input speed revolution will be out.
D.
If output speed revolution is output. It means that the foot brake force is not applied fully. Remeasuring is required.
5.
Is "STALL TEST " within specification?
▶ Go to "Signal circuit inspection" procedure.
▶ Go to "Component inspection" procedure.
caution
1.
Do not let anybody stand in front of or behind the vehicle while this test is being carried out.
2.
Check the A/T fluid level and temperature and the engine coolant temperature.
●
Fluid level : At the hot mark on the oil level gauge.
●
Fluid temperature : 176 °F~ 212 °F (80~100 °C).
●
Engine coolant temperature : 176 °F~ 212 °F (80~100 °C).
3.
Chock both rear wheel(left and right).
4.
Pull the parking brake lever on with the brake pedal fully depressed.
5.
The throttle should not be left fully open for more than eight second.
6.
If carrying out the stall test two or more time, move the select lever to the "N" position and run the engine at 1,000 rpm to let the A/T fluid cool down before carrying out subsequent.
SIGNAL CIRCUIT INSPECTION
1.
Connect Scantool.
2.
Engine "ON".
3.
Monitor the "INPUT ＆ OUTPUT SPEED SENSOR" parameter on the scantool.
4.
Accelerate the Engine speed until about 2000 rpm in the 2nd gear.
Does "INPUT ＆ OUTPUT SPEED SENSOR" within specifications?
▶ Go to "Component Inspection" procedure.
▶ Check for electrical noise of circuit in INPUT ＆ OUTPUT SPEED SENSOR or Replace INPUT ＆ OUTPUT SPEED SENSOR. Repair as necessary and Go to "Verification of Vehicle Repair" procedure.
COMPONENT INSPECTION
1.
Connect oil pressure gauge to "UD" and "2-4/B" port.
2.
Engine "ON".
3.
Drive a car with gear position 2 in "SPORTS MODE".
4.
Compare it with reference data as below.
Specification :
Standard hydraulic pressure table
5.
Is oil pressure value within specifications?
▶ Repair AUTO TRANSAXLE(Clutch or Brake) as necessary and Go to "Verification of Vehicle Repair" procedure.
▶ Replace AUTO TRANSAXLE (BODY CONTROL VALVE faulty) as necessary and Go to "Verification of Vehicle Repair " procedure.
VERIFICATION OF VEHICLE REPAIR
After a repair, it is essential to verify that the fault has been corrected.
1.
Connect scantool and select "Diagnostic Trouble Codes(DTCs)" mode.
2.
Using a scantool, Clear DTC.
3.
Operate the vehicle within DTC Enable conditions in General information.
4.
Are any DTCs present ?
▶ Go to the applicable troubleshooting procedure.
▶ System performing to specification at this time.
