Description
Burglar Alarm System

The burglar alarm system is armed automatically after the doors, hood, and tailgate are closed and locked.

The system is set off when any of these things occur :

●

A door is forced open.

●

The tailgate is opened.

●

The hood is opened.

When the system is set off, the alarm sounds and the hazard lamp flash for about 30 seconds or until the system is disarmed by unlocking the transmitter or door key.

For the system to arm, the ignition switch must be off and the key removed. Then, the body control module must receive signals that the doors, hood, and tailgate are closed and locked. When everything is closed and locked, none of the control unit inputs are grounded.

The door switches, hood switch and tailgate switch are all close and lock the doors with the remote transmitter and then the system arms immediately.

If anything is opened after the system is armed, the body control module gets a ground signal from that switch, and the system is set off.

If one of the switches is misadjusted or there is a short in the system, the system will not arm. As long as the body control module continues to get a ground signal, it thinks the vehicle is not closed and locked and will not arm.

Keyless Entry System

The burglar alarm system is integrated with the keyless entry system. The keyless entry system allows you to lock and unlock the vehicle with the remote transmitter. When you push the LOCK button, all doors lock. When you push the UNLOCK button again, all doors unlock.

The room lamp, if its switch is in the center position, will come on when you press the UNLOCK button. If you do not open a door, the light will go off in about 30 seconds, the doors will automatically relock, and the burglar alarm system will rearm. If you relock the doors with the remote transmitter within 30 seconds, the light will go off immediately.

You cannot lock or unlock the doors with the remote transmitter if the key is in the ignition switch.

The system will signal you when the doors lock and unlock by flashing the hazard lamp once when they lock, and twice when they unlock.

Function
Keyless Entry Function

DOOR LOCK / UNLOCK and Tailgate (Folding key only) operation are performed with remocon

1.

Keyless entry function is performed in a state that key in SW is eliminated from key cylinder

2.

LOCK / UNLOCK and tailgate signals are received from the transmitter and DOOR LOCK / UNLOCK and Tailgate signals are output.

Transmitter(tx) Spec
1.

Transmission Distance : 30m or more from outside of the car

2.

Registration procedure of the transmitter

(1)

In registration mode, it shall be possible to register up to Max 4EA.

(2)

At re-registration, data are registered newly after deleting the previous TX DATA

No.

Saved CODE

CODE to change

Changed CODE

1

-

A

A

2

A

B

B (A is deleted)

3

B

C, D

C, D (B is deleted)

4

C, D

E, F, G

E, F, G (C, D is deleted)

5

E, F, G

H, I, J, K

H, I, J, K (E, F, G are deleted)

6

A, B

C, F, E, F, G

C, F, E, F

7

A, B

C, C, D, E, F

C, D, E, F

8

A, B, C, D

A

A

9

A, B, C, D

E

E

(3)

For the registration procedures by using Hi-scan tool, refer to "TRANSMITTER CODE REGISTRATION".

3.

Transmitter signal & Receiver Spec

(1)

Transmission signal

A.

Transmit relevant transmission DATA (Transmission frame) twice by pushing TX SW.

B.

Only LOCK signal is output when pushing TX LOCK SW and UNLOCK SW at the same time.

DISARM
Condition 1

State

Description

Initial Condition

ALARM state

Event

●

IGN KEY ON during 30sec or ALT"L" = ON

●

TX(Transmitter) Unlock & Any Door open(4Door SW ON)

●

TX(Transmitter) Lock & Lock confirm failed

●

Driver door key unlock switch ON.

●

Driver door key lock SW ON & Lock confirm failed

●

TX tailgate ON (Folding key type only : 3 button).

Action

●

The state goes to DISARM state

●

Hazard relay off, Horn relay off and start inhibit relay off.

●

TX Unlock

-

Unlock relay on for 0.5 sec.

-

Hazard relay on (TWICE)

Condition 2

State

Description

Initial Condition

DISARM state & (IGN KEY OUT) & Any Door open

Event

●

TX Unlock

Action

●

No state change

●

TX UNLOCK

-

Unlock relay on for 0.5 sec

-

Hazard relay on (Twice)

Condition 3

State

Description

Initial Condition

ARMWAIT state

Event

●

At least one entrance opened

●

Any door is unlocked

●

Key in SW ON

●

Driver door key unlock SW ON

Action

The state goes to DISARM state

Condition 4

State

Description

Initial Condition

AUTOLOCKTIMER1 state

Event

●

At least one entrance opened

●

Key in SW ON

●

Lock by AUTOLOCK, but Lock confirmation failure

●

Tx Lock, but Lock confirmation failure

●

Driver door key unlock SW ON, but Lock confirmation failure

Action

●

The state goes to DISARM state

Condition 5

State

Description

Initial Condition

AUTOLOCKTIMER2 state

Event

●

Any Door open

●

Key in SW ON

●

Lock by AUTOLOCK, but Lock confirmation failure

●

Tx Lock, but Lock confirmation failure

●

Driver door key lock SW ON, but Lock confirmation failure

Action

●

The state goes to DISARM state

Condition 6

State

Description

Initial Condition

ARM state

Event

●

IGN KEY ON

●

Driver door key unlock SW ON

Action

●

The state goes to DISARM state

Condition 7

State

Description

Initial Condition

REARM state

Event

●

IGN KEY ON during 30sec or ALT"L" = ON

●

Tx Lock, but Lock confirmation failure

●

Driver door key unlock SW ON

●

Driver door key lock SW ON & Lock confirmation failure

●

TX tailgate ON (Folding key type only : 3 button).

Action

●

The state goes to DISARM state

●

Start Inhibit relay OFF

Condition 8

State

Description

Initial Condition

PREARM state

Event

●

Key in SW ON

●

All entrance closed & Any Door is unlocked

●

Any Door open & Tx Unlock

Action

●

The state goes to DISARM state

●

TX UNLOCK

-

Unlock relay on for 0.5sec

-

Hazard relay on (Twice)

Condition 9

State

Description

Initial Condition

AutoLockTimer3 state

Event

●

Key in SW ON

●

Hood open

●

Any Door open

●

Lock confirm failed

Action

●

The state goes to DISARM state

ARM
-

LED is Blinking

Condition 1

State

Description

Initial Condition

ARM state

Event

●

Tx Lock

Action

●

No state change

●

Hazard relay 1Time on(1sec)

Condition 2

State

Description

Initial Condition

ARMWAIT state

Event

●

ARMWAITTIMER is expired

Action

●

The state goes to ARM state

ALARM
-

LED is Blinking

Condition 1

State

Description

Initial Condition

ARM state

Event

●

Any entrance open (DOORS, TAILGATE, or HOOD)

Action

●

The state goes to ALARM state

●

The horn is ON one time for 27sec(±2sec)

●

The hazard is driven also (During Horn driving)

●

Engine Start Inhibit is ON

T1 : 27s ± 2sec, T2 : 0.5s ± 0.1sec.

note

Horn Output : Period : 1sec(Can be calibrated Horn Period), 50% Duty

Condition 2

State

Description

Initial Condition

REARM state

Event

●

Any door open or Hood open or tailgate open

Action

●

The state goes to ALARM state

●

The horn is ON one time for 27sec (±2sec.)

●

The hazard is driven also (During horn driven)

ARM WAIT MODE
-

LED is turn on

Condition 1

State

Description

Initial Condition

ARMWAIT state

Event

●

Tx Lock

Action

●

The state goes to State

●

TX LOCK

-

Hazard relay 1 Time on(1sec)

Condition 2

State

Description

Initial Condition

DISARM state & IGN KEY OUT & All entrances closed (DOORS, HOOD and TAILGATE)

Event

●

Tx Lock & locked confirmed

●

Driver door key lock SW ON & Locked confirmed

Action

●

The state goes to ARMWAIT State

●

Start ARMWAITTIMER

●

TX LOCK & locked confirmed.

-

Hazard relay 1 Time on (1 sec.)

Condition 3

State

Description

Initial Condition

ALARM state & All entrances closed(DOORS, HOOD and TAILGATE)

Event

●

Tx Lock & locked confirmed

●

Driver door key lock SW ON & Locked confirmed

Action

●

The state goes to ARMWAIT state

●

Start ARMWAITTIMER

●

Horn relay off

●

Start inhibit relay off

●

Hazard relay 1Time on(1sec)

Condition 4

State

Description

Initial Condition

AUTOLOCKTIMER1 state

Event

●

AUTO LOCK confirmed

●

Tx Lock & locked confirmed

●

Driver door key lock SW ON & Locked confirmed

Action

●

The state goes to ARMWAIT state

●

Start ARMWAITTIMER

●

Hazard relay 1Time on(1sec)

Condition 5

State

Description

Initial Condition

PREARM state

Event

●

Hood and 4door are closed & All doors locked & Tailgate closed.

Action

●

The state goes to ARMWAIT state

●

Start ARMWAITTIMER

●

Hazard relay 1Time on(1sec)

●

Dead lock

●

Tailgate mark = set

Condition 6

State

Description

Initial Condition

REARM state

Event

●

Tx Lock & locked confirmed

●

Drive door key lock SW ON & locked confirmed

Action

●

The state goes to ARMWAIT state

●

Start ARMWAITTIMER

●

Start inhibit relay off

●

Hazard relay 1Time on(1sec)

Condition 7

State

Description

Initial Condition

Auto Lock Timer3 state

Event

●

Tx Lock & locked confirmed

●

Drive door key lock SW ON & locked confirmed

Action

●

The state goes to ARMWAIT state

●

Start ARMWAITTIMER

●

Start inhibit relay off

●

Hazard relay 1Time on(1sec)

REARM MODE
-

LED is Blinking

Condition 1

State

Description

Initial Condition

ALARM state

Event

●

All entrance is closed & Alarm Patten finished

Action

●

The state goes to REARM state

AUTOLOCKTIMER1 MODE
-

LED is Blinking

Condition 1

State

Description

Initial Condition

ARM state

Event

●

Tx Unlock

Action

●

The state goes to AUTOLOCKTIMER1 state

●

Start AUTOLOCKTIMER1

●

Hazard relay Twice on(0.5s ON/0.5s OFF)

Condition 2

State

Description

Initial Condition

AUTOLOCKTIMER1 state

Event

●

Timer is expired

●

Tx Unlock

Action

●

The state goes to State

●

Tx Unlock

-

Hazard relay Twice on(0.5s ON/0.5s OFF)

-

Restart AUTOLOCKTIMER1

●

Expire AUTOLOCKTIMER1

-

AUTOLOCK

Condition 3

State

Description

Initial Condition

ARMWAIT state

Event

●

Tx Unlock

Action

●

The state goes to AUTOLOCKTIMER1 state

●

Start AUTOLOCKTIMER1

●

Hazard relay Twice on(0.5s ON/0.5s OFF)

Condition 4

State

Description

Initial Condition

DISARM state & All entrances closed (DOORS, HOOD & TAILGATE) & IGN KEY OUT

Event

●

Tx Unlock

Action

●

The state goes to AUTOLOCKTIMER1 state

●

Start AUTOLOCKTIMER1

●

Hazard relay Twice on(0.5s ON/0.5s OFF)

Condition 5

State

Description

Initial Condition

ALARM state & All entrances are closed (DOORS, HOOD & TAILGATE)

Event

●

Tx Unlock

Action

●

The state goes to AUTOLOCKTIMER1 state

●

Start AUTOLOCKTIMER1

●

Hazard relay Twice on(0.5s ON/0.5s OFF)

●

Start inhibit relay off

●

Horn relay off

Condition 6

State

Description

Initial Condition

REARM state

Event

●

Tx Unlock

Action

●

The state goes to AUTOLOCKTIMER1 state

●

Start AUTOLOCKTIMER1

●

Hazard relay Twice on(0.5s ON/0.5s OFF)

●

Start inhibit relay off

Condition 7

State

Description

Initial Condition

Auto Lock Timer3 state

Event

●

Tx Unlock

Action

●

The state goes to AUTOLOCKTIMER1 state

●

Start AUTOLOCKTIMER1

●

Hazard relay Twice on(0.5s ON/0.5s OFF)

AUTOLOCKTIMER2 MODE
-

LED is blinking

Condition 1

State

Description

Initial Condition

AUTOLOCKTIMER2 state

Event

●

Timer is expired

●

Tx Unlock

Action

●

No State change

●

Tx Unlock

-

Hazard relay Twice on(0.5s ON/0.5s OFF)

-

The timer restart

●

Expire AUTOLOCKTIMER2

-

AUTOLOCK

Condition 2

State

Description

Initial Condition

DISARM state & All Doors are closed & (HOOD is opened) & IGN KEY OUT

Event

●

Tx Unlock

Action

●

The state goes to AUTOLOCKTIMER2 state

●

Start AUTOLOCKTIMER2

●

Hazard relay Twice on(0.5s ON/0.5s OFF)

Condition 3

State

Description

Initial Condition

ALARM state & All Door are closed & (HOOD is opened)

Event

●

Tx Unlock

Action

●

The state goes to AUTOLOCKTIMER2 state

●

Start AUTOLOCKTIMER2

●

Hazard relay Twice on(0.5s ON/0.5s OFF)

●

Start inhibit relay off

●

Horn relay off

Condition 4

State

Description

Initial Condition

PREARM state

All Doors are closed & (HOOD is opened)

Event

●

Tx Unlock

Action

●

The state goes to AUTOLOCKTIMER2 state

●

Start AUTOLOCKTIMER2

●

Memorize Hood and Tailgate state

●

Hazard relay Twice on(0.5s ON/0.5s OFF)

AUTO LOCK TIMER3 MODE

- LED is blinking

Condition 1

State

Description

Initial Condition

ARM state

Event

●

Tx TAILGATE Unlock

Action

●

The state goes to AUTO LOCK RELAY TIMER3 state

●

Start AUTO LOCK RELAY TIMER3

●

Hazard relay Twice on(0.5s ON/0.5s OFF)

●

TAILGATE Mark=set

●

Dead unlock

Condition 2

State

Description

Initial Condition

AutoLockTimer3 state

Event

●

Tx TAILGATE Unlock

Action

●

Restart AUTO LOCK TIMER3 state

Condition 3

State

Description

Initial Condition

ARMWAIT state

Event

●

Tx TAILGATE Unlock

Action

●

The state goes to AUTO LOCK RELAY TIMER3 state

●

Start AUTO LOCK RELAY TIMER3

●

Dead Unlock

●

Hazard relay Twice on(0.5s ON/0.5s OFF)

●

TAILGATE Mark=set

PREARM MODE
-

LED is blinking

Condition 1

State

Description

Initial Condition

AUTOLOCKTIMER2 state

Event

●

AUTOLOCK confirmed

●

Tx Lock & locked confirmed

●

Driver door key lock SW ON & Locked confirmed

Action

●

The state goes to PREARM state

Condition 2

State

Description

Initial Condition

DISARM state & IGN KEY OUT

Event

●

((4Door Not Closed = ON & Tailgate SW = OFF or (Hood SW = ON)) & Tx Lock & Locked confirmed

●

((4Door Not Closed = ON & Tailgate SW = OFF or (Hood SW = ON)) & driver door key lock SW ON on & Locked confirmed

Action

●

The state goes to PREARM state

Condition 3

State

Description

Initial Condition

ALARM state & Hood SW = ON

Event

●

Tx Lock & Locked confirmed

●

Driver door key lock SW ON & Locked confirmed

Action

●

The state goes to PREARM state

●

Start inhibit relay off

●

Horn relay off

●

Hazard relay 1Time on (1sec.)

Condition 4

State

Description

Initial Condition

AUTOLOCKTIMER3 state

Event

●

Expire Auto Lock Timer3

●

Tailgate open

Action

●

The state goes to PREARM state.

RESET
1.

In case of taking the battery out during the ALARM state

Condition 1

State

Description

Initial Condition

During ALARM, REARM

Event

●

TAKING THE BATTERY OUT (Cold or Warm RESET)

Action

●

The state goes to ALARM mode

●

Horn relay 1 Times on (No remained time of warning signal)

●

Hazard lamp is flashing during making horn

2.

In case of taking the battery out during arm

Condition 2

State

Description

Initial Condition

ARM state

Event

●

TAKING THE BATTERY OUT (Cold or Warm RESET)

Action

●

The state goes to ARM mode

●

Maintained ARM state

The Restricted Function Of Unlock By Centrol Door Lock Sw
1.

In IGN Key OUT, UNLOCK is restricted by Central Door Lock SW if All DR LOCK & CLOSED when TX LOCK.

2.

In IGN Key OUT, UNLOCK is restricted by Central Door Lock SW if All DR LOCK & CLOSED when DR LOCK by DRV DR Key.

3.

The restricted function of UNLOCK is canceled when TX UNLOCK signal output during the restricted function of Central Door Lock SW.

4.

The restricted function of UNLOCK is canceled when DR UNLOCK signal output during the restricted function of Central Door Lock SW.

T1 : 0.5s ± 0.1s

Tailgate Release Function
Permissive Mode State

State

Description

Initial Condition

PROHIBITIONAL MODE STATE

Event

Any Door Unlocked

Operating

MOVE TO PERMISSIVE MODE STATE

State

Description

Initial Condition

30s PERMISSIVE MODE STATE

Event

Any Door Unlocked

Operating

MOVE TO PERMISSIVE MODE STATE

State

Description

Initial Condition

PERMISSIVE MODE STATE

Event

TAILGATE RELEASE SW = ON

Operating

●

TAILGATE RELEASE RELAY 0.5SEC ON

●

MOVE TO PERMISSIVE MODE STATE

30s Permissive Mode State

State

Description

Initial Condition

PROHIBITIONAL MODE STATE

Event

TAILGATE UNLOCK

Operating

●

START TAILGATE TIMER

●

HAZARD 2 FLASHING

●

MOVE TO 30s PERMISSIVE MODE STATE

State

Description

Initial Condition

30s PERMISSIVE MODE STATE

Event

TAILGATE UNLOCK

Operating

●

RESTART TGATE TIMER

●

HAZARD 2 times FLASHING

●

MOVE TO 30s PERMISSIVE MODE STATE

State

Description

Initial Condition

30s PERMISSIVE MODE STATE

Event

TAILGATE RELEASE SW = ON

Operating

●

TAILGATE RELEASE RELAY OUTPUT FOR 0.5s

●

MOVE TO 30s PERMISSIVE MODE STATE

Prohibitional Mode State

State

Description

Initial Condition

30s PERMISSIVE MODE STATE

Event

●

TAILGATE OPEN→CLOSE

●

4Door Lock Confirm

Operating

MOVE TO PROHIBITIONAL MODE STATE

State

Description

Initial Condition

30s PERMISSIVE MODE STATE

Event

TAILGATE TIMER IS EXPIRED

Operating

MOVE TO PROHIBITIONAL MODE STATE

State

Description

Initial Condition

PERMISSIVE MODE STATE

Event

4Door Lock Confirm

Operating

MOVE TO PROHIBITIONAL MODE STATE

Яндекс.Метрика