1.
Install the transaxle lower mounting bolts (A-3ea,B-2ea) after fitting the transaxle assembly into the engine assembly.
Tightening torque :
[A] 43-49 Nm (4.3-4.9kgf.m, 31.1-35.4 lb-ft)
[B] 43-55 Nm (4.3-5.5kgf.m, 31.1-39.8 lb-ft)
Install the transaxle lower mounting bolts (A-3ea,B-2ea) after fitting the transaxle assembly into the engine assembly.
Tightening torque :
[A] 43-49 Nm (4.3-4.9kgf.m, 31.1-35.4 lb-ft)
[B] 43-55 Nm (4.3-5.5kgf.m, 31.1-39.8 lb-ft)
Install the clutch release cylinder assembly (A).
Tightening torque :
12-22 Nm (1.2-2.2kgf.m, 8.7-15.9 lb-ft)
Install the bracket (A,B)
Tightening torque :
46-53 Nm (4.6-5.3kgf.m, 33.3-38.3 lb-ft)
Connect the drive shafts (A,B) to the transaxle.
Supporting the sub frame (A) with a jack and the Special tool(09624-38000), install the mounting bolts. (refer to Stabilizer installation in SS group)
Tightening torque :
140-160Nm (14-16kgf.m, 101-118lb-ft)
Install the muffler hanger rubber (A).
Install the roll stopper bracket bolts. (A,B)
Tightening torque :
50-65Nm (5-6.5kgf.m, 36.2-47.0lb-ft)
Install the under shield cover. (A,B)
Install the lower arm ball joint mounting nut, the stabilizer link mounting nut, and the tie rod end mounting nut to the front knuckles. (refer to Front suspension system in SS group)
Install the front wheels and tires. (refer to installation in SS group)
Install the steering joint assembly bolt (A). (refer to Steering column/shaft in ST group)
Tightening torque :
18-25Nm (1.8-2.5kgf.m, 13.0-18.1lb-ft)
Install the transaxle insulator mounting bracket bolts (A).
Tightening torque :
60-80Nm (6.0-8.0kgf.m, 43.4-57.9lb-ft)
Install the transaxle upper mounting bolts (A-2ea) the starter motor mounting bolts. (B-2ea)
Tightening torque :
[A] 43-55Nm (4.3-5.5kgf.m, 31.1-39.8lb-ft)
[B] 43-55Nm (4.3-5.5kgf.m, 31.1-39.8lb-ft)
Remove the special tool (09200-38001).
Connect the vehicle speed sensor connector (A).
Install the shift cable bracket bolts (B-3ea) and the snap pins (A).
Tightening torque :
15-22Nm (1.5-2.2 kgf.m, 10.8-15.9lb-ft)
Connect the back up lamp switch connector (A).
Install the wire bracket (A).
Connect the neutral switch connector (A).
Install the lower cover of the air cleaner assembly (B) and connect the PCM connector (A).
Connect the air intake hose (A).
Install the upper cover of the air cleaner assembly (C) by connecting the accelerating cable (B) and tightening the clamp (A).
Install the battery (A) and the battery terminal.
Install the engine cover. (refer to Engine and Transaxle Assembly in EM group)
