Disconnect the battery negative terminal.

Remove the air cleaner assembly.

<a href="content.asp?vehicletype=Passenger&mfrcode=KM&area=KME&langcode=ENG&modelid=JD12&modelyr=2013&mmctype=en&mmcid=109&group=SHOP&pdftype=&cat1=2013+%3E+G+1%2E6+MPI&ec=&firstnodedesc=Engine+Mechanical+System&sitinfolist=12%5E1235%5E12350100%5Enone%5E801%5E1%5EENG%5EKM%5EJD12%5E2013%5Een%5E109%5Enone%5Enone%5Enone%5ESHOP%5E%24" target="_blank">(Refer to Engine Mechanical System - "Air cleaner")</a>

Remove the battery tray.

<a href="content.asp?vehicletype=Passenger&mfrcode=KM&area=KME&langcode=ENG&modelid=JD12&modelyr=2013&mmctype=en&mmcid=109&group=SHOP&pdftype=&cat1=2013+%3E+G+1%2E6+MPI&ec=&firstnodedesc=Engine+Electrical+System&sitinfolist=11%5E1125%5E11250200%5Enone%5E801%5E1%5EENG%5EKM%5EJD12%5E2013%5Een%5E341%5Enone%5Enone%5Enone%5ESHOP%5E%2411%5E1125%5E11250200%5Enone%5E801%5E8%5EENG%5EKM%5EJD12%5E2013%5Een%5E341%5Enone%5Enone%5Enone%5ESHOP%5E%2411%5E1125%5E11250200%5Enone%5E801%5E4%5EENG%5EKM%5EJD12%5E2013%5Een%5E341%5Enone%5Enone%5Enone%5ESHOP%5E%2411%5E1125%5E11250200%5Enone%5E801%5E3%5EENG%5EKM%5EJD12%5E2013%5Een%5E341%5Enone%5Enone%5Enone%5ESHOP%5E%24" target="_blank">(Refer to Engine Electrical System - "Battery")</a>

Disconnect the over flow hose (A) from the radiator.

Loosen the drain plug, and drain the engine coolant. Remove the radiator cap to drain with speed.

Disconnect the radiator upper hose (A) and lower hose (B).

Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).

Remove the front bumper.

<a href="content.asp?vehicletype=Passenger&mfrcode=KM&area=KME&langcode=ENG&modelid=JD12&modelyr=2013&mmctype=bd&mmcid=4&group=SHOP&pdftype=&cat1=2013+%3E+G+1%2E6+MPI&ec=&firstnodedesc=Body+%28Interior+and+Exterior%29&sitinfolist=91%5E9181%5E91810010%5Enone%5E801%5E6%5EENG%5EKM%5EJD12%5E2013%5Ebd%5E4%5Enone%5Enone%5Enone%5ESHOP%5E%24" target="_blank">(Refer to Body - "Front Bumper")</a>

Remove the air guard (A).

Remove the upper mounting bracket (A).

Separate the condenser from the radiator and then pull the radiator (A) upper from vehicle.

Remove the cooling fan & reservior tank (A) from the radiator (B).

Installation is reverse order of removal.

Fill the radiator with coolant and check for leaks.

Put the radiator cap on tightly, then run engine again and check for leaks.

Remove the radiator cap, wet its seal with engine coolant, and then install it on a pressure tester.

Apply a pressure of 93.16 ~ 122.58kpa (0.95 ~ 1.25kg/cm², 13.51 ~ 17.78psi).

Check for a drop in pressure.

If the pressure drops, replace the cap.

Wait until engine is cool, then carefully remove the radiator cap and fill the radiator with engine coolant, then install a pressure tester on it.

Apply a pressure of 93 ~ 123kPa (0.95 ~ 1.25kgf/cm², 14 ~ 19psi).

Inspect for engine coolant leaks and a drop in pressure.

If the pressure drops, check hoses, the radiator and the water pump for leakage. If there is no leakage, inspect the heater core, the cylinder block and the cylinder head.

Remove the tester and reinstall the radiator cap.