Turn the ignition switch OFF.
Disconnect the mode control actuator connector.
Verify that the mode control actuator operates to the defog mode when connecting 12V to terminal 3 and grounding terminal 4.
Verify that the mode control actuator operates to the vent mode when connected in reverse.
1. - 2. - 3. Defog mode 4. Sensor ground | 5. Feedback signal 6. Sensor (+ 5V) 7. Vent mode |
Connect the mode control actuator connector.
Turn the ignition switch ON.
Check the voltage between terminal 4 and 5.
Specification
With auto defogging activated
Door position | Voltage (V) | Error detecting |
Vent | 0.3 | Low voltage : 0.1V or less |
Vent / Defog | 1.03 | |
Vent / Defog / Floor | 2.5 | |
Bi-Level | 1.77 |
|
Floor | 3.23 |
|
Mix | 3.97 |
|
Defog | 4.7 | High voltage : 4.9V or more |
It will feedback the current position of the actuator to the controls.
If the measured voltage is not within specification, substitute with a known-good mode control actuator and check for proper operation.
If the problem is corrected, replace the mode control actuator.
Disconnect the negative (-) battery terminal.
Remove the crash pad lower panel.
<a href="content.asp?vehicletype=Passenger&mfrcode=KM&area=KME&langcode=ENG&modelid=JD12&modelyr=2013&mmctype=bd&mmcid=4&group=SHOP&pdftype=&cat1=2013+%3E+G+1%2E6+MPI&ec=&firstnodedesc=Body+%28Interior+and+Exterior%29&sitinfolist=91%5E9154%5E91540040%5Enone%5E801%5E6%5EENG%5EKM%5EJD12%5E2013%5Ebd%5E4%5Enone%5Enone%5Enone%5ESHOP%5E%24"target="_blank">(Refer to Body - "Crash Pad Lower Panel")</a>
Remove the driver side shower duct (A) after loosening the screw.
Remove the brake pedal assembly.
<a href="content.asp?vehicletype=Passenger&mfrcode=KM&area=KME&langcode=ENG&modelid=JD12&modelyr=2013&mmctype=br&mmcid=19&group=SHOP&pdftype=&cat1=2013+%3E+G+1%2E6+MPI&ec=&firstnodedesc=Brake+System&sitinfolist=41%5E4110%5E41100500%5Enone%5E801%5E1%5EENG%5EKM%5EJD12%5E2013%5Ebr%5E19%5Enone%5Enone%5Enone%5ESHOP%5E%2441%5E4110%5E41100500%5Enone%5E801%5E4%5EENG%5EKM%5EJD12%5E2013%5Ebr%5E19%5Enone%5Enone%5Enone%5ESHOP%5E%2441%5E4110%5E41100500%5Enone%5E801%5E8%5EENG%5EKM%5EJD12%5E2013%5Ebr%5E19%5Enone%5Enone%5Enone%5ESHOP%5E%2441%5E4110%5E41100500%5Enone%5E801%5E5%5EENG%5EKM%5EJD12%5E2013%5Ebr%5E19%5Enone%5Enone%5Enone%5ESHOP%5E%24"target="_blank">(Refer to Brake System - " Brake Pedal")</a>
Disconnect the connector (A) and then remove the mode control actuator (B) after loosening the mounting screws.
Install in the reverse order of removal.
