2.
Disconnect the clutch motor connector (A).
Turn off the ignition switch.
Disconnect the clutch motor connector (A).
Measure the resistance on the clutch motor terminal.
Refer to the specifications and check that the measured resistance is as specified.
(Refer to Clutch Actuator Motor 2 - "Specification")
Turn off the ignition switch and then disconnect the battery (-) cable.
Remove the air cleaner assembly and air duct.
<a href="content.asp?vehicletype=Passenger&mfrcode=KM&area=KME&langcode=ENG&modelid=JD12&modelyr=2013&mmctype=en&mmcid=88&group=SHOP&pdftype=&cat1=2013+%3E+G+1%2E6+GDI&ec=&firstnodedesc=Engine+Mechanical+System&sitinfolist=12%5E1235%5E12350100%5Enone%5E801%5E1%5EENG%5EKM%5EJD12%5E2013%5Een%5E88%5Enone%5Enone%5Enone%5ESHOP%5E%24" target="_blank">(Refer to Engine Mechanical System - "Air cleaner")</a>
Remove the battery and battery tray.
<a href="content.asp?vehicletype=Passenger&mfrcode=KM&area=KME&langcode=ENG&modelid=JD12&modelyr=2013&mmctype=en&mmcid=88&group=SHOP&pdftype=&cat1=2013+%3E+G+1%2E6+GDI&ec=&firstnodedesc=Engine+Electrical+System&sitinfolist=11%5E1125%5E11250200%5Enone%5E801%5E1%5EENG%5EKM%5EJD12%5E2013%5Een%5E88%5Enone%5Enone%5Enone%5ESHOP%5E%2411%5E1125%5E11250200%5Enone%5E801%5E8%5EENG%5EKM%5EJD12%5E2013%5Een%5E88%5Enone%5Enone%5Enone%5ESHOP%5E%2411%5E1125%5E11250200%5Enone%5E801%5E4%5EENG%5EKM%5EJD12%5E2013%5Een%5E88%5Enone%5Enone%5Enone%5ESHOP%5E%2411%5E1125%5E11250200%5Enone%5E801%5E3%5EENG%5EKM%5EJD12%5E2013%5Een%5E88%5Enone%5Enone%5Enone%5ESHOP%5E%24" target="_blank">(Refer to Engine Electrical System - "Battery")</a>
Remove the ECM.
<a href="content.asp?vehicletype=Passenger&mfrcode=KM&area=KME&langcode=ENG&modelid=JD12&modelyr=2013&mmctype=en&mmcid=88&group=SHOP&pdftype=&cat1=2013+%3E+G+1%2E6+GDI&ec=&firstnodedesc=Fuel+System&sitinfolist=14%5E1420%5E14200100%5Enone%5E801%5E1%5EENG%5EKM%5EJD12%5E2013%5Een%5E88%5Enone%5Enone%5Enone%5ESHOP%5E%2414%5E1420%5E14200100%5Enone%5E801%5E8%5EENG%5EKM%5EJD12%5E2013%5Een%5E88%5Enone%5Enone%5Enone%5ESHOP%5E%2414%5E1420%5E14200100%5Enone%5E801%5E4%5EENG%5EKM%5EJD12%5E2013%5Een%5E88%5Enone%5Enone%5Enone%5ESHOP%5E%24" target="_blank">(Refer to Fuel System - "Engine Control Module (ECM)")</a>
Disconnect the clutch actuator motor connector (A).
Loosen the mounting screw, and then remove the clutch actuator motor (A).
Tightening Torque :
4.4 ~ 5.4 N.m (0.45 ~ 0.55 kgf.m, 3.3 ~ 4.0 lb-ft)
Install in the reverse order of removal.
Clutch actuator spline (A) with grease before installation.
Specified grease [CSG-101M (0.1ml)]
