3.
Remove the parking brake cable (A), after removing the clip (B).
note
Parking brake lever in the car must be in fully loosened position.
Remove the rear wheel ＆ tire.
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)
Release the parking brake lever and parking brake cable is loose.
Remove the parking brake cable (A), after removing the clip (B).
Parking brake lever in the car must be in fully loosened position.
Loosen the guide rod bolt (A) and then remove the rear caliper body (B).
Tightening torque:
21.6 ~ 31.4 N.m (2.2 ~ 3.2 kgf.m, 15.9 ~23.1 lb-ft)
Where necessary prevent the guide rods from rotating with an appropriate wrench.
Be careful not to damage the dust covers.
Replace pad retainers (C) and brake pads (B) in the caliper carrier (A).
Clean the pad retainer surface at the caliper bracket.
Inspect the piston boots for damage and replace if necessary.
Check the smooth action of the guide rods, and their dust covers for damage.
Insert the piston in the cylinder the SST(09580-0U000).
Place the caliper body (B) on the caliper carrier and tighten the guide rod bolts (A).
Tightening torque:
21.6 ~ 31.4 N.m (2.2 ~ 3.2 kgf.m, 15.9 ~ 23.1 lb-ft)
Assemble the caliper body so that the piston groove (A) is in-line with the pad center lobe (B).
* Make sure that the piston and pad are tightly attached.
Install the rear wheel & tire.
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)
Remove the rear wheel ＆ tire.
Connect the GDS to the data link connector located underneath the dash panel.
Ignition "ON" & Engine "OFF".
Release the electric parking brake.
Select vehicle name and EPB system.
Select the “PAD change mode”.
Perform the " PAD change mode (Before pad change)" procedure with GDS.
When disengaging while the motor is in operation, be sure to press down on the brake pedal.
Ignition "OFF".
Disconnect the electric parking brake actuator connector (A).
Loosen the guide rod bolts (B) and then remove caliper body (A).
Replace pad retainers (C) and brake pads (B) in the caliper carrier (A).
Insert the piston in the cylinder the SST(09580-0U000).
Place the caliper body (A) on the caliper carrier and tighten the guide rod bolts (B).
Tightening torque:
21.6 ~ 31.4 N.m (2.2 ~ 3.2 kgf.m, 15.9 ~ 23.1 lb-ft)
Assemble the caliper body so that the piston groove (A) is in-line with the pad center lobe (B).
* Make sure that the piston and pad are tightly attached.
Connect the electric parking brake actuator connector (A).
Ignition "ON".
Select the “PAD change mode”.
Perform the " PAD change mode (Before pad change)" procedure with GDS.
Check that the parking brake operates normally.
When you activate the EPB for the first time after you change the brake pad, be sure to press down on the brake pedal.
IGN switch “OFF” and remove the GDS.
Install the rear wheel ＆ tire.
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)
