Items | Specification | |
Fuel Tank | Capacity | 53 lit (14.0 U.S.gal., 56.0 U.S.qt., 46.6 lmp.qt.) |
Fuel Filter | Type | Paper type |
Fuel Pressure | RegulatedFuel Pressure | 323 ~ 363kpa (3.29 ~ 3.70kgf/㎠, 46.85 ~ 52.65psi) |
Fuel Pump | Type | Electrical, in-tank type |
Driven by | Electric motor | |
Supply Voltage | 12 ~ 14.3 V | |
Current | Max. 6.0 A | |
Fuel Retrun System | Type | Returnless |
Throttle Position Sensor (TPS) [integrated into ETC module]
Item | Opening Percentage (%) | Output Voltage (V) [Vref = 5V] | |
TPS1 | C.T | 8.5 ~ 11.5 | 0.43 ~ 0.58 |
W.O.T | 88 ~ 96 | 4.40 ~ 4.80 | |
TPS2 | C.T | 88.5 ~ 91.5 | 4.43 ~ 4.58 |
W.O.T | 2 ~ 10 | 0.10 ~ 0.50 | |
Fail Safe | Throttle valve stuck at 5° | ||
Supply Voltage (V) | 4.8 ~ 5.2 | ||
Type | Hall IC Non-contact sensor [Integrated into ETC Module] |
DC Motor [integrated into ETC module]
Item | Specification |
Coil Resistance (Ω) | 0.3 ~ 100 [20℃(68℉)] |
Maximum Allowable Current (A) | < 10.0 |
Type | DC Motor [Integrated into ETC Module] |
▷ Type: Piezo-resistive pressure sensor type
Pressure [kPa (kgf/cm², psi)] | Output Voltage (V) [Vref = 5V] |
20.0 (0.20, 2.9) | 0.79 |
46.7 (0.47, 6.77) | 1.84 |
101.32 (1.03, 14.7) | 4.0 |
▷ Type: Thermistor type
Temperature | Resistance (㏀) | |
℃ | ℉ | |
-40 | -40 | 40.93 ~ 48.35 |
-30 | -22 | 23.43 ~ 27.34 |
-20 | -4 | 13.89 ~ 16.03 |
-10 | 14 | 8.5 ~ 9.7 |
0 | 32 | 5.38 ~ 6.09 |
10 | 50 | 3.48 ~ 3.90 |
20 | 68 | 2.31 ~ 2.57 |
30 | 86 | 1.9 ~ 2.1 |
40 | 104 | 1.08 ~ 1.21 |
50 | 122 | 0.76 ~ 0.85 |
60 | 140 | 0.54 ~ 0.62 |
70 | 158 | 0.40 ~ 0.45 |
80 | 176 | 0.29 ~ 0.34 |
90 | 194 | 0.22 ~ 0.26 |
100 | 212 | 0.17 ~ 0.20 |
110 | 230 | 0.13 ~ 0.15 |
120 | 248 | 0.10 ~ 0.12 |
130 | 266 | 0.08 ~ 0.09 |
▷ Type: Thermistor type
Temperature | Resistance (㏀) | |
℃ | ℉ | |
-40 | -40 | 48.14 |
-20 | -4 | 14.13-16.83 |
0 | 32 | 5.79 |
20 | 68 | 2.31-2.59 |
40 | 104 | 1.15 |
60 | 140 | 0.59 |
80 | 176 | 0.32 |
100 | 212 | 0.19 |
110 | 230 | 0.145 ~ 0.149 |
120 | 248 | 0.12 |
NON- ISG Type
Item | Specification |
Type | Magnetic field sensitive type |
Coil Resistance (Ω) | 819 ~ 1001 [20°C (68℉)] |
Pin | 2 |
With ISG Type
Item | Specification |
Type | Hall effect type |
Air Gap (mm) | 0.9 ~ 1.1 |
Pin | 3 |
Item | Specification |
Type | Hall effect type |
Output Pulse (V) | 0 ~ 5 |
Air Gap [mm (in.)] | 0.2 ~ 2.0 (0.0079 ~ 0.079) |
Pin | 3 |
Item | Specification |
Resistance(㏁) | 4.87 |
Capacitance (pF) | 950 ~ 1,350 |
Type | Piezo-electricity |
Pin | 2 |
HO2S [Bank 1/Sensor 1]
Item | Specification |
Heater Resistance (Ω) | Approximately 9.0 [20℃(68℉)] |
Type | Binary |
Pin | 4 |
HO2S [Bank 1/Sensor 2]
Item | Specification |
Heater Resistance (Ω) | Approximately 9.0 [20℃(68℉)] |
Type | Binary |
Pin | 4 |
Accelerator Position | Output Voltage (V) [Vref = 5V] | |
APS1 | APS2 | |
C.T | 0.7 ~ 0.8 | 0.29 ~ 0.46 |
W.O.T | 3.85 ~ 4.35 | 1.93 ~ 2.18 |
Item | Specification | |
Coil Resistance (Ω) | 13.8 ~ 15.2 [20℃ (68℉)] | |
Minimum Injection Time (ms) | 1.8 | |
Fuel Pressure | bar | 2 ~ 7 |
kPa | 200 ~ 700 | |
kgf/cm² | 2.04 ~ 7.14 | |
psi | 29.0 ~ 101.5 | |
Pin | 2 |
Item | Specification |
Coil Resistance (Ω) | 16.0 [20℃(68℉)] |
Pin | 2 |
[Bank 1 / Intake]
Item | Specification | |
Coil Resistance (Ω) | 6.9 ~ 7.9 [20℃(68℉)] | |
Control Current (mA) | 100 ~ 1000 | |
Reted Voltage (V) | 12 | |
Insulation resistance (MΩ) | 50 [DC 500 V/1 Min] | |
Oil Pressure | bar | 2.9 ~ 3.1 |
kPa | 290 ~ 310 | |
kgf/cm² | 2.96 ~ 3.16 | |
psi | 42.1 ~ 44.96 | |
Pin | 2 |
[Bank 1 / Exhaust]
Item | Specification | |
Coil Resistance (Ω) | 6.9 ~ 7.9 [20℃(68℉)] | |
Control Current (mA) | 100 ~ 1000 | |
Reted Voltage (V) | 12 | |
Insulation resistance (MΩ) | 50 [DC 500 V/1 Min] | |
Oil Pressure | bar | 2.9 ~ 3.1 |
kPa | 290 ~ 310 | |
kgf/cm² | 2.96 ~ 3.16 | |
psi | 42.1 ~ 44.96 | |
Pin | 2 |
Ignition Timing | BTDC 6° ± 10° | ||
Idle Speed | A/CON OFF | Neutral,N,P-range | 660 ± 100 rpm |
D-range | 660 ± 100 rpm | ||
A/CON ON | Neutral | 660 ± 100 rpm | |
D, N, P-range | 660 ± 100 rpm |
Item | Kgf.m | N.m | lb-ft |
ECM mounting screws | 0.09 - 0.097 | 0.9 - 0.95 | 0.66 - 0.7 |
ECM bracket mounting bolt / nut | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
Electronic Throttle Control (ETC) moule mounting bolt | 0.8 - 1.0 | 7.8 - 9.8 | 5.8 - 7.2 |
Engine Coolant Temperature Sensor (ECTS) | 2.0 - 4.0 | 19.6 - 39.2 | 14.4 - 28.9 |
Crankshaft Position Sensor (CKPS) mounting bolt | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
Camshaft position sensor [Bank 1 / Intake] mounting bolt | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
Camshaft position sensor [Bank 1 / Exhaust] mounting bolt | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
Knock Sensor (KS) mounting bolt | 1.9 - 2.4 | 18.6 - 23.5 | 13.7 - 17.4 |
Heated oxygen sensor [Bank 1 / Sensor 1] | 4.0 - 5.0 | 39.2 - 49.1 | 28.9 - 36.2 |
Heated oxygen sensor [Bank 1 / Sensor 2] | 4.0 - 5.0 | 39.2 - 49.1 | 28.9 - 36.2 |
Accelerator pedal position sensor (APS) mounting nut[APS integrated into Accelerator pedal module] | 1.3 - 1.6 | 12.7 - 15.7 | 9.4 - 11.6 |
Accelerator pedal position sensor (APS) mounting bolt[APS integrated into Accelerator pedal module] | 0.9 - 1.04 | 8.8 - 13.7 | 6.5 - 10.1 |
CVVT Oil Control Valve (OCV) [Bank 1 / Intake] mounting bolt | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
CVVT Oil Control Valve (OCV) [Bank 1 / Exhaust] mounting bolt | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
Item | Kgf.m | N.m | lb-ft |
Fuel tank mounting nut | 4.0 - 5.5 | 39.2 - 53.9 | 28.9 - 39.8 |
Fuel pump plate cover mounting bolt | 0.2 - 0.3 | 2.0 - 2.9 | 1.4 - 2.2 |
Filler-neck assembly mounting bolt | 0.8 - 1.2 | 7.8 - 11.8 | 5.8 - 8.7 |
Filler-neck assembly bracket mounting bolt | 0.4 - 0.6 | 3.9 - 5.9 | 2.9 - 4.3 |
Delivery pipe mounting bolt | 1.9 - 2.4 | 18.6 - 23.5 | 13.7 - 17.4 |
Delivery pipe mounting nut(↔ Fuel feed tube) | 0.4 - 0.6 | 3.9 - 5.9 | 2.9 - 4.3 |