Inspection
1.

Check for resistance or output voltage between terminals in each switch position.

[Audio]

Switch

Connector terminal

Resistance (±5%)

Output voltage

Seek up

2-4

430 Ω

0.4 V ± 0.22

Seek down

2-4

1.1 kΩ

1.0 V ± 0.22

Mode

2-4

2.11 kΩ

1.5 V ± 0.22

Mute

2-4

3.11 kΩ

2.0 V ± 0.22

Volume up

2-4

4.61 kΩ

2.5 V ± 0.22

Volume down

2-4

6.81 kΩ

3.0 V ± 0.22

[Cruise/Criuse+LDWS]

Switch

Connector terminal

Resistance (±5%)

Output voltage

Cancel

2-4

180 Ω

0.8 V ± 0.17

Set

2-4

330 Ω

1.2 V ± 0.17

Resume

2-4

550 Ω

1.8 V ± 0.22

Cruise

2-4

880 Ω

2.3 V ± 0.22

LDWS

2-4

1.44 Ω

3.0 V ± 0.22

Speed limit

2-4

2.54 kΩ

3.6 V ± 0.22

[Voice + Bluetooth]

Switch

Connector terminal

Resistance (±5%)

Output voltage

Voice

2-4

10.71 kΩ

3.5 V ± 0.22

Call off

2-4

18.91 kΩ

4.0 V ± 0.22

Call

2-4

40.91 kΩ

4.5 V ± 0.22

[Flex steer + Trip + Reset]

Switch

Connector terminal

Resistance (±5%)

Output voltage

Flex steer

2-4

180 Ω

0.8 V ± 0.17

Trip

2-4

330 Ω

1.2 V ± 0.17

Reset

2-4

550 Ω

1.8 V ± 0.22

Removal
[Upper Steering Wheel Remote Control Switch]
1.

Disconnect the negative (-) battery terminal.

2.

Remove the driver airbag module.

(Refer to the RT group)

3.

Remove the steering wheel.

(Refer to the ST group - "Steering column & shaft")

4.

Loosen the mounting screws from the rear steering wheel cover.

5.

Separate the upper steering wheel remote control switch (A) from the steering wheel.

[LH]
[RH]
6.

Remove the upper steering wheel control switch (B) disconnecting the connector (A).

[LH]
[RH]
[Lower Steering Wheel Remote Control Switch]
1.

Disconnect the negative (-) battery terminal.

2.

Remove the driver airbag module.

(Refer to the RT group)

3.

Remove the steering wheel.

(Refer to the ST group - "Steering column & shaft")

4.

Loosen the mounting screws from the rear steering wheel cover.

5.

Separate the upper steering wheel remote control switch (A) from the steering wheel.

[LH]
[RH]
6.

Remove the upper steering wheel control switch (B) disconnecting the connector (A).

[LH]
[RH]
7.

Separate the lower steering wheel control switch (A) loosening the mounting screws.

[LH]
[RH]
8.

Remove the lower steering wheel control switch (B) disconnecting the connector (A).

[LH]
[RH]
Installation
1.

Install the remote control switch on the steering wheel.

2.

Install the steering wheel.

3.

Reconnect the remote control switch connector and airbag connectors.

note

Make sure that the switch connector is plugged in properly.

4.

Install the driver airbag module.

5.

Connect the negative (-) battery terminal.

Яндекс.Метрика