1.
Drain engine oil.
(1)
Remove the oil filler cap.
(2)
After lifting the car, remove the oil drain plug (A) and drain oil into a container.
[Nu 2.0 MPI]
[Gamma 1.6 GDI, MPI, FFV]
[U2 1.6 TCI]
Prolonged and repeated contact with mineral oil will result in the removal of natural fats from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
Exercise caution in order to minimize the length and frequency of contact of your skin to used oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use water-less hand cleaner, to remove any used engine oil. Do not use gasoline, thinners, or solvents.
In order to preserve the environment, used oil and used oil filter must be disposed of only at designated disposal sites.
Drain engine oil.
Remove the oil filler cap.
After lifting the car, remove the oil drain plug (A) and drain oil into a container.
Replace the oil filter.
Remove the oil filter cap (A).
Using the SST (09263-2E000), remove the oil filter (A).
Check and clean the oil filter installation surface.
Check the part number of the new oil filter is as same as old one.
Apply clean engine oil to the gasket of a new oil filter.
Lightly screw the oil filter into place, and tighten it until the gasket contacts the seat.
Tighten it with the torque below.
Tightening torque :
11.8 ~ 15.7 N.m (1.2 ~ 1.6 kgf.m, 8.7 ~ 11.6 lb-ft)
Replace the oil filter (A).
Remove the oil filter upper cap (B).
Replace the O-ring (C, D) of oil filter cap with a new one.
Inspect the threads and O-ring (C, D). Wipe off the seat on the oil filter cap, then apply a light coat of oil to the oil filter upper cap O-ring (C, D).
Install the new oil filter by hand to the upper cap.
After the rubber seal seats, tighten the oil filter clockwise.
Tightening torque : 31.5 ~ 38.5 N.m (3.2 ~ 3.9 kgf.m, 23.2 ~ 28.4 lb-ft)
Install the oil drain plug with a new gasket.
Tightening torque :
34.3 ~ 44.1 N.m (3.5 ~ 4.5 kgf.m, 25.3 ~ 32.5 lb-ft)
Fill with new engine oil, after removing the engine oil level gauge.
Capacity
[Nu 2.0 MPI]
Total: 4.5 L (1.19 U.S.gal., 4.76 U.S.qt., 3.96 lmp.qt.)
Oil pan: 3.7 L (0.98 U.S.gal., 3.91 U.S.qt., 3.26 lmp.qt.)
Drain and refill including oil filter:
4.0 L (1.06 U.S.gal., 4.23 U.S.qt., 3.52 lmp.qt.)
[Gamma 1.6 GDI, MPI, FFV]
Total : 3.7 ~ 4.0L (0.98 ~ 1.06 U.S.gal, 3.91 ~ 4.22U.S.qt., 3.25 ~ 3.51lmp.qt.)
Oil pan : 3.3 L (0.87 U.S.gal., 3.48 U.S.qt., 2.90 lmp.qt.)
Drain and refill in cluding oil filter :
3.6 L (0.95 U.S.gal., 3.80 U.S.qt., 3.16 lmp.qt.)
[U2 1.6 TCI]
Total : 5.7 L (1.51 U.S.gal., 6.02 U.S.qt., 5.01 lmp.qt.)
Oil pan : 4.8 L (1.27 U.S.gal., 5.07 U.S.qt., 4.22 lmp.qt.)
Drain and refill including oil filter :
5.3 L (1.40 U.S.gal., 5.60 U.S.qt., 4.66 lmp.qt.)
Install the oil filler cap.
Start engine and check for oil leaks and check the oil gauge or light for an indication of oil pressure.
Recheck the engine oil level.
