3.
Disconnect the connectors in the illustration below and then loosen the ground line mounting bolt (A).
(B) Inhibitor switch connector
(C) Clutch actuator connector
(D) Gear actuator solenoid connector
(E) Vehicle speed sensor connector
Remove the air cleaner assembly.
(Refer to Engine Mechanical System - "Air Cleaner")
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
Disconnect the connectors in the illustration below and then loosen the ground line mounting bolt (A).
(B) Inhibitor switch connector
(C) Clutch actuator connector
(D) Gear actuator solenoid connector
(E) Vehicle speed sensor connector
Disconnect the gear actuator motor connector (A).
Remove the wiring bracket mounting bolts (A).
Tightening torque :
9.8 ~ 11.8 N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7 lb-ft)
Remove the shift cable (C) after loosening the nut (A) and bolt (B).
Tightening torque :
(A) 9.8 ~ 13.7 N.m (1.0 ~ 1.4 kgf.m, 7.2 ~ 10.8 lb-ft)
(B) 19.6 ~ 26.5 N.m (2.0 ~ 2.7 kgf.m, 14.5 ~ 19.5 lb-ft)
Loosen the ground bolt (A).
Tightening torque :
9.8 ~ 11.8 N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7 lb-ft)
Loosen the transmission upper mounting bolts (A: 2 pcs) and starter mounting bolts (B: 2 pcs).
Tightening torque :
(A) 58.8 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)
(B) 49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)
Install the engine support fixture.
Loosen the bolts (A) from both side.
Assemble the engine support fixture.
(Refer to Special Service Tools-"Engine support fixture assembly drawing")
Remove the cover (A).
Remove the transaxle mounting bracket bolts (A).
Tightening torque :
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.8 lb-ft)
Remove the transmission support bracket (A).
Tightening torque :
58.8 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)
Remove the under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
Remove the sub frame.
(Refer to Suspension System - "Sub Frame")
Remove the drive shaft assembly.
(Refer to Driveshaft and Axle - "Front Driveshaft")
Remove the CKP sensor (A).
Remove the cover (A).
Loosen the intercooler inlet pipe mounting bolts (A: 2 pcs).
Support the transmission safety on a jack.
Loosen the transmission lower mounting bolts (A: 3 pcs, B: 2 pcs).
Tightening torque :
(A) 34.3 ~ 49.0 N.m (3.5 ~ 5.0 kgf.m, 25.3 ~ 36.2 lb-ft)
(B) 42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
After separating the transmission from the engine, remove the transmission by lowering the jack slowly.
Be careful not to damage other nearby systems or parts when removing the transmission assembly.
Remove the dual clutch from the transmission.
(Refer to Dual Clutch System - "Dual Clutch Assembly")
