1.
Using a screwdriver or remover, remove the front door quadrant inner cover (A).
Be careful not to scratch the door trim and other parts.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the front door quadrant inner cover (A).
Disconnect the tweeter speaker connector (A).
Remove the front door handle cap (B) and front door pull handle cap (C).
After loosening the mounting screw, then remove the front door inside handle cover (A).
After loosening the mounting screw, then remove the front door trim (A).
Disconnect the outside rear view mirror connector (A) and power window connector (B).
Installation is the reverse of removal.
Make sure connectors are connected properly and each rod is connected securely.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Remove the front door trim.
After loosening the mounting screw, then remove the front door inside handle (A).
Disconnect the front door inside handle cable (A).
Installation is the reverse of removal.
Replace any damaged clips.
Make sure the door lock and opens properly.
Remove the front door trim.
After loosening the mounting screw, then remove the front door inside handle (A).
Disconnect the front door inside handle cable (A).
Disconnect the front door speaker connector (A).
Disconnect the outside rear view mirror connector (A).
After loosening the mounting screws, then remove the front door trim seal mounting bracket (B).
Remove the front door trim seal (A).
Replace any damaged door trim seal.
Remove the front door belt inside weatherstrip (A).
Carefully move the glass (A) until you can see the screws, then loosen them. Separate the glass from the glass run and carefully pull the glass out through the window slot.
Take care not to drop to glass and scratch the glass surface.
Tightening torque :
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)
Installation is the reverse of removal.
Roll the glass up down to see if it move freely without binding.
Adjust the position of the glass as necessary.
Remove the front door trim.
Disconnect the speaker connector (B).
Drill out the rivets to remove the speaker (A).
Installation is the reverse of removal.
Use sheet metal screws to secure the speaker.
Make sure connectors are connected properly and each rod is connected securely.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Remove the following items.
Front door trim
Front door trim seal
Front door glass
Loosen the front door power window regulator mounting nuts.
Disconnect the front door power window motor connector (A).
Tightening torque :
3.9 ~ 5.9N.m (0.4 ~ 0.6kgf.m, 2.9 ~ 4.3 lb-ft)
Remove the front door power window regulator assembly (A).
Installation is the reverse of removal.
Grease should be applied to areas where there is rotational parts and springs.
Roll the glass up and down to see if it move freely without binding.
Remove the following items.
Front door trim
Front door trim seal
After loosening the mounting bolt, then remove the outside handle cover (A).
Tightening torque :
6.9 ~ 10.8N.m (0.7 ~ 1.1kgf.m, 5.1 ~ 8.0lb-ft)
Remove the outside handle (A) by sliding it rearward.
Disconnect the outside handle connector (A).
Installation is the reverse of removal.
Make sure the door locks/unlocks and opens/closes properly.
Make sure the connectors are connected in properly.
Replace any damage clips.
Remove the following items.
Front door trim
Front door trim seal
After loosening the mounting bolt, then remove the outside handle cover (A).
Tightening torque:
6.9 ~ 10.8N.m (0.7 ~ 1.1kgf.m, 5.1 ~ 8.0lb-ft)
Disconnect the key holder rod (A).
Remove the key holder (A).
Installation is the reverse of removal.
Replace any damage clips.
Remove the following items.
Front door trim
Front door trim seal
Disconnect the key holder rod (A) and outside handle rod (B).
Loosen the front door latch (A) mounting screws.
Tightening torque:
7.8 ~ 10.8N.m (0.8 ~ 1.1kgf.m, 5.8 ~ 8.0 lb-ft)
Disconnect the front door latch connector (A).
Remove the front door latch assembly (A).
Installation is the reverse of removal.
Make sure the door locks/unlocks and opens/closes properly.
Make sure the connectors are connected in properly.
Replace any damage clips.
Loosen the checker mounting bolts.
Detach the clips, then remove the front door side weatherstrip (A).
Installation is the reverse of removal.
Replace any damage clips.
