1.
Using a screwdriver or remover, remove te rear door delta inner cover (A).
Be careful not to scratch the door trim and other parts.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove te rear door delta inner cover (A).
Remove the rear door handle cap (B) and rear door pull handle cap (C).
After loosening the mounting screw, then remove the rear door inside handle cover (A).
After loosening the mounting screw, then remove the rear door trim (A).
Disconnect the power window connector (A).
Installation is the reverse of removal.
Make sure connectors are connected properly and each rod is connected securely.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Remove the rear door trim.
After loosening the mounting screw, then remove the rear door inside handle (A).
Disconnect the rear door inside handle rod (A).
Installation is the reverse of removal.
Replace any damaged clips.
Make sure the door lock and opens properly.
Remove the rear door trim.
After loosening the mounting screw, then remove the rear door inside handle (A).
Disconnect the rear door inside handle cable (A).
Disconnect the rear door speaker connector (A).
After loosening the mounting screws, then remove the rear door trim seal mounting bracket (B).
Remove the rear door trim seal (A).
Replace any damaged door trim seal.
After loosening the mounting screws, then remove the rear door delta molding (A).
Loosen the rear door channel mounting bolts and nut.
Tightening torque :
3.9 ~ 5.9N.m (0.4 ~ 0.6kgf.m, 2.9 ~ 4.3 lb-ft)
Remove the rear door belt inside weatherstrip (A).
Carefully move the glass (A) until you can see the screws, then loosen them. Separate the glass from the glass run and carefully pull the glass out through the window slot.
Take care not to drop to glass and scratch the glass surface.
Tightening torque :
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)
Installation is the reverse of removal.
Roll the glass up down to see if it move freely without binding.
Adjust the position of the glass as necessary.
Remove the rear door trim.
Disconnect the speaker connector (B).
Drill out the rivets to remove the speaker (A).
Installation is the reverse of removal.
Use sheet metal screws to secure the speaker.
Make sure connectors are connected properly and each rod is connected securely.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Remove the following items.
Rear door trim
Rear door trim seal
Rear door glass
Loosen the rear door power window regulator mounting nuts.
Disconnect the rear door power window motor connector (A).
Tightening torque :
3.9 ~ 5.9N.m (0.4 ~ 0.6kgf.m, 2.9 ~ 4.3 lb-ft)
Remove the rear door power window regulator assembly (A).
Installation is the reverse of removal.
Grease should be applied to areas where there is rotational parts and springs.
Roll the glass up and down to see if it move freely without binding.
Remove the following items.
Rear door trim
Rear door trim seal
After loosening the mounting bolt, then remove the outside handle cover (A).
Tightening torque:
6.9 ~ 10.8N.m (0.7 ~ 1.1kgf.m, 5.1 ~ 8.0lb-ft)
Remove the outside handle (A) by sliding it rearward.
Installation is the reverse of removal.
Make sure the door locks/unlocks and opens/closes properly.
Make sure the connectors are connected in properly.
Replace any damage clips.
Remove the following items.
Rear door trim
Rear door trim seal
Disconnect the outside handle rod (A).
Loosen the rear door channel mounting bolts and nut.
Tightening torque:
3.9 ~ 5.9N.m (0.4 ~ 0.6kgf.m, 2.9 ~ 4.3 lb-ft)
Remove the rear door channel (A).
Loosen the rear door latch (A) mounting screws.
Tightening torque:
7.8 ~ 10.8N.m (0.8 ~ 1.1kgf.m, 5.8 ~ 8.0 lb-ft)
Disconnect the rear door latch connector (A).
Remove the rear door latch assembly (A).
Installation is the reverse of removal.
Make sure the door locks/unlocks and opens/closes properly.
Make sure the connectors are connected in properly.
Replace any damage clips.
Loosen the checker mounting bolts.
Detach the clips, then remove the rear door side weatherstrip (A).
Installation is the reverse of removal.
Replace any damage clips.
