Remove the following items;
Air cleaner assembly and air duct (A).
(Refer to "Intake and Exhaust system" in EM group.)
Battery and battery tray (B).
(Refer to "Charging system" in EE group.)
ECM (C).
(Refer to "Engine Control System" in FL group.)
Remove the control cable.
(1) Remove the control cable from the control shaft after removing the pins (A).
Loosen the control cable bracket bolts (B).
Tightening torque :
14.7-21.6 N.m (1.5-2.2 kgf.m, 10.8-15.9 lb-ft)
Disconnect the back up lamp switch connector (A).
Remove the ground cable from transaxle (A).
Remove the clutch tube bracket bolt (A).
Tightening torque:
14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.8 ~ 15.9 lb-ft)
Remove the transaxle upper mounting bolt (A-2ea) and the start motor mounting bolt (B-2ea).
Tightening torque:
(A) 42.2 ~ 54.0 N.m(4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
(B) 38.2 ~ 58.8 N.m (3.9 ~ 6.0 kgf.m, 28.2 ~ 43.4 lb-ft)
Remove the cowl top cover.
(Refer to "Interior(cowl top cover)" in BD group.)
Using the engine support fixture (Support SST No.: 09200-2S100/2S200, Adapter SST No.: 09200-4X000, Beam SST No.: 09200-38001/3N000), hold the engine and transaxle assembly safely.
Remove the mounting cover (A).
Remove the transaxle support mounting bracket bolts (A-2ea).
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)
Remove the transaxle support bracket (A).
Tightening torque:
58.9 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)
Remove the under cover (A).
Remove the clutch release cylinder assembly (B) after removing the bolts (A-2ea)
Tightening torque:
14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.8 ~ 15.9 lb-ft)
Remove the brackets (A).
Remove the roll rod bracket (C) after removing bolt (A,B).
Tightening torque:
(A) 49.0 ~ 68.6 N.m (5.0 ~ 7.0 kgf.m, 36.2 ~ 50.6 lb-ft)
(B) 107.9 ~ 127.5 N.m (11 ~ 13 kgf.m, 79.6 ~ 94.1 lb-ft)
Remove the plastic dust cover (A).
Remove the drive shaft assembly.
(Refer to "Drive shaft assembly" in DS group.)
Remove the mounting bolts (A-3ea, B-2ea) of lower part of the transaxle, and the left side cover and remove the transaxle assembly by supporting it with a jack.
Be careful not to damage other system or parts near by when removing the engine and transaxle assembly.
Tightening torque:
(A) 42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)
(B) 42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
