1.
Using a screwdriver or remover, remove the front door quadrant inner cover (A).
Be careful not to scratch the door trim and other parts.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the front door quadrant inner cover (A).
After loosening the mounting screws, then remove the front door trim (A).
Remove the inside handle cage (A).
Disconnect the connectors (A).
Installation is the reverse of removal.
Make sure connectors are connected properly and each rod is connected securely.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Remove the front door trim
After loosening the mounting screws, then remove the inside handle (A).
Installation is the reverse of removal.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Remove the front door trim.
Disconnect the speaker connector (B).
After loosening the mounting screws, then remove the speaker (A).
Remove the front door belt inside weatherstrip (A).
Remove the glass mounting hole plug (B).
Use the door switch to align the mounting hole/bolt with the hole in the door.
If unable to operate the window motor, remove the motor and align the hole by hand.
Be careful not to drop the glass and/or scratch the glass surface.
Carefully adjust the glass (A) until you can see the bolts, then loosen them. Separate the glass from the glass run and carefully pull the glass out through the window slot.
Tightening torque :
3.9 ~ 2.9 N.m (0.4 ~ 1.2 kgf.m, 11.8 ~ 8.7 lb-ft)
Installation is the reverse of removal.
Roll the glass up and down to see if it moves freely without binding.
Adjust glass position as needed.
Make sure the door lock and opens properly.
Replace any damaged clips.
Remove the front door trim.
Disconnect the speaker connector (B).
After loosening the mounting screws, then remove the speaker (A).
Installation is the reverse of removal.
Use sheet metal screws to secure the speaker.
Replace any damaged clips.
Make sure the door locks/unlocks and opens/closes properly.
Make sure connectors are connected properly and each rod is connected securely.
Remove the front door trim.
Disconnect the power window motor connector (B).
After loosening the mounting screws, then remove the power window motor (A).
Installation is the reverse of removal.
Grease should be applied to areas where there is rotational parts and springs.
Roll the glass up and down to see if it moves freely without binding.
Replace any damaged clips.
Make sure the door locks/unlocks and opens/closes properly.
Remove the following parts:
Front door trim
Window glass
Outside handle
Loosen the mounting bolt (A).
After loosening the door module mounting bolts, then remove the front door module (A).
Tightening torque:
6.9~10.8 N.m (0.7~1.1 kgf.m, 5.1~8.0 lb-ft)
Disconnect the outside handle connector (A) and outside handle rod (B).
Disconnect the connectors and door module wiring harness (A).
Installation is the reverse of removal.
The area of whole parts should be applied with sufficient grease.
Make sure connectors are connected properly and each rod is connected securely.
Make sure the door locks/unlocks and opens/closes properly.
Remove the front door trim.
Remove the front door module.
Remove the hole plug (B).
After loosening the mounting bolt, then remove the outside handle cover (A).
Tightening torque:
0.7 ~ 0.5 N.m (0.07 ~ 0.1 kgf.m, 1.0 ~ 0.7 lb-ft)
Remove the outside handle (A) by sliding it rearward.
Disconnect the outside handle connector (A).
Installation is the reverse of removal.
Make sure the door locks/unlocks and opens/closes properly.
Make sure the door locks and opens properly.
Remove the following items :
Front door trim
Window glass
Outside handle
Loosen the mounting bolt (A).
After loosening the door module mounting bolts, then remove the front door module (A).
Tightening torque:
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Disconnect the outside handle connector (A).
Disconnect the connector (C) and rod (B).
Remove the rear door latch (A).
Installation is the reverse of removal.
Make sure the connector is connected properly.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Loosen the checker mounting bolts.
Detach the clips, then remove the front door side weatherstrip (A).
Installation is the reverse of removal.
