2.
Remove the ground line after removing the bolt (A).
Remove the following items;
Engine cover.
Air cleaner assembly and air duct.
(Refer to "Intake and Exhaust system" in EM group)
Battery and battery tray.
(Refer to "Charging system" in EE group)
Remove the ground line after removing the bolt (A).
Remove the shift cable (C) after remove the nut (A) and bolts (B).
Tightening torque:
(A) 9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)
(B) 14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)
Dissconnect the solenoid valve connector (A) and inhibitor switch connector (B).
Remove the wiring bracket (A).
Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).
Remove the wiring bracket installation bolt (A).
Using the engine support fixture (SST No.: 09200-38001), hold the engine and transaxle assembly safely.
Remove the automatic transaxle upper mounting bolts (A-2ea) and the starter motor mounting bolts (B-2ea).
Tightening torque
(A): 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
(B): 49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)
Remove the transaxle mounting support bracket bolt (B) after removing a cover (A).
Tightening torque:
107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94.0 lb-ft)
Remove the transaxle mounting support bracket (C) after removing nuts (A) and bolts (B).
Tightening torque:
(A) 78.5 ~ 98.1 N.m (8.0 ~ 10.0 kgf.m, 57.9 ~ 72.3 lb-ft)
(B) 58.9 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)
Remove the under cover (A).
Tightening torque:
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Remove the drive shaft assembly.
(Refer to "Drive shaft assembly" in DS group.)
Remove the sub frame.
(Refer to "Front cross member" in SS group.)
Remove the bracket (A).
Remove the drive shaft cover (A).
Remove the dust cover (A).
Tightening torque:
42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)
Remove the torque converter mounting bolt (A-4ea) with rotating the crankshaft.
Tightening torque:
45.1 ~ 52.0 N.m (4.6 ~ 5.3 kgf.m, 33.3 ~ 38.3 lb-ft)
Remove the automatic transaxle with a jack after removing the mounting bolt (A-1ea, B-3ea).
Tightening torque:
(A) 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
(B) 42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)
Installation is the reverse of removal.
If the oil seal on the transaxle case side is damaged and fluid is leaking, replace the oil seal with a new unit. When installing the new oil seal, use the specialized tool (oil seal installer, 09453-3L241).
After replacement or reinstallation procedure of the automatic transaxle assembly, must perform procedures below.
Adding automatic transaxle fluid. (Refer to "Hydraulic system (Fluid)" in this group)
After servicing the automatic transaxle or TCM, clear the diagnostic trouble codes (DTC) using the GDS tool.
Diagnostic trouble codes (DTC) cannot be cleared by disconnecting the battery.
When deleting diagnostic trouble code, use the GDS as possible.
When replacing the automatic transaxle, reset the automatic transaxle's values by using the GDS.
Perform TCM learning after replacing the transaxle to prevent slow transaxle response, jerky acceleration and jerky startup. (Refer to "Automatic transaxle control system (Repair procedures)" in this group)
When replacing the automatic transaxle, reset the automatic transaxle's values by using the GDS.
[Condition]
IG Key On
Transaxle Range:P
Vehicle Speed :0 km/h
Engine Off
