7949288

Many malfunctions in the electrical system are caused by poor harness and terminals.

Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage.

Thoroughly check all connectors (and connections) for looseness, bending, corrosion, contamination, deterioration, and/or damage.

Has a problem been found?

	▶ Repair as necessary and then go to "Verification of Vehicle Repair" procedure.
	▶ Go to "TPS Circuit Inspection" procedure.

Refer to "Shop Manual" and disconnect Throttle Body connector.

Measure voltage between Pin No. 5 (TPS Supply) terminal of Throttle Body Sensor harness connector and chassis ground.

Specification : Approx. 5 V

Is measured value within specification?

	▶ Go to "Ground Circuit Inspection" procedure.
	▶ Repair open or short in power circuit between Throttle Body and ECM/PCM and then go to "Verification of vehicle Repair" procedure.

Disconnect Battery (-) terminal.

Refer to "Shop Manual" and disconnect Throttle Body connector.

Measure resistance between Pin No. 1 (Ground) terminal of Throttle Body harness connector and chassis ground

Specification : Approx. below 1 Ω

11.

Disconnect Battery (-) terminal.

12.

Refer to "Shop Manual" and disconnect PCM connector.

13.

Measure resistance between Pin No. 1 (Ground) terminal of Throttle Body harness connector and Pin No. 54 (Ground) terminal of PCM harness connector.

Specification : Approx. below 1 Ω

14.

Is measured value within specification?

	▶ Go to "Signal Circuit Inspection" procedure.
	▶ Repair open or short in ground circuit between Throttle Body and chassis ground and then go to "Verification of vehicle Repair" procedure.

16.

Refer to "Shop Manual" and disconnect Throttle Body connector.

18.

Measure voltage between Pin No. 4 (TPS1 Signal) terminal of Throttle Body harness connector and chassis ground.

Specification : Approx. 4 V

19.

Measure voltage between Pin No. 5 (TPS2 Signal) terminal of Throttle Body harness connector and chassis ground.

Specification : Approx. 0 V

21.

Disconnect Battery (-) terminal.

22.

Refer to "Shop Manual" and disconnect PCM connector.

23.

Measure resistance between Pin No. 4 (TPS1 Signal) terminal of Throttle Body harness connector and Pin No. 96 (TPS1 Signal) terminal of PCM harness connector.

24.

Measure resistance between Pin No. 5 (TPS2 Signal) terminal of Throttle Body harness connector and Pin No. 75 (TPS2 Signal) terminal of PCM harness connector.

Specification : Approx. below 1 Ω

25.

Is measured value within specification?

	▶ Go to "ETC Motor Circuit Inspection" procedure.
	▶ Repair open or short in signal circuit between Throttle Body and PCM and then go to "Verification of vehicle Repair" procedure.

Refer to "Shop Manual" and disconnect Throttle Body connector.

Measure voltage between Pin No. 5 (Motor +) terminal of Throttle Body Sensor harness connector and chassis ground.

Specification : Approx. 1.9 V

Is the measured value within specification?

	▶ Go to next procedure.
	▶ Repair open or short in ETC Motor(+) circuit between Throttle Body and PCM and then go to "Verification of vehicle Repair" procedure.

Disconnect Battery (-) terminal.

Refer to "Shop Manual" and disconnect Throttle Body and PCM connector.

Measure voltage between Pin No. 5 (Motor -) terminal of Throttle Body Sensor harness connector and Pin No. 6 (Motor -) terminal of PCM harness connector.

Specification : Approx. below 1 Ω

10.

Is the measured value within specification?

	▶ Go to "Component Inspection" procedure.
	▶ Repair open or short in ETC Motor(-) circuit between Throttle Body and PCM and then go to "Verification of vehicle Repair" procedure.