1.
After loosening the mounting screws, then remove the rear door trim (A).
Be careful not to scratch the door trim and other parts.
Put on gloves to protect your hands.
After loosening the mounting screws, then remove the rear door trim (A).
Disconnect the inside handle cage (A).
Disconnect the connector (A).
Installation is the reverse of removal.
Make sure connectors are connected properly and each rod is connected securely.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Remove the rear door trim.
After loosening the mounting screws, then remove the inside handle (A).
Installation is the reverse of removal.
Make sure the door locks/unlocks and opens/closes properly.
Replace any damaged clips.
Remove the rear door trim.
Disconnect the speaker connector (B).
After loosening the mounting screws, then remove the speaker (A).
After loosening the mounting screws, then remove the rear door pull handle mounting support (B).
Remove the rear door trim seal (A).
Replace ant damaged door trim seal.
Remove the rear door belt inside weatherstrip (A).
Using a screwdriver or remover, remove the rear door upper opening weatherstrip (A).
Using a screwdriver or remover, remove the rear door frame moulding (A).
Rear door frame moulding needs to be changed to insure product quality.
After loosening the mounting screw and bolt, then remove the rear door div channel (A).
Remove the rear door window glass run (B) and then remove the rear door fixed glass (A).
Remove the glass mounting hole plug (B).
Take care not to drop to glass and scratch the glass surface.
Carefully adjust the glass (A) until you can see the bolts, then loosen them. Separate the glass from the glass run and carefully pull the glass out through the window slot.
Tightening torque:
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)
Installation is the reverse of removal.
Roll the glass up and down to see if it move freely without binding.
Adjust glass position as needed.
Remove the rear door trim.
Disconnect the speaker connector (B).
After loosening the mounting screws, then remove the speaker (A).
Installation is the reverse of removal.
Use sheet metal screws to secure the speaker.
Replace ant damaged clips.
Make sure the door locks/unlocks and opens/closes properly.
Make sure connectors are connected properly and each rod is connected securely.
Remove the rear door trim.
Disconnect the speaker connector (B).
After loosening the mounting screws, then remove the speaker (A).
After loosening the mounting screws, then remove the rear door pull handle mounting support (B).
Remove the rear door trim seal (A).
Replace ant damaged door trim seal.
Remove the rear door belt inside weatherstrip (A).
Using a screwdriver or remover, remove the rear door upper opening weatherstrip (A).
Using a screwdriver or remover, remove the rear door frame moulding (A).
Rear door frame moulding needs to be changed to insure product quality.
After loosening the mounting screw and bolt, then remove the rear door div channel (A).
Remove the rear door window glass run (B) and then remove the rear door fixed glass (A).
Remove the glass mounting hole plug (B).
Take care not to drop to glass and scratch the glass surface.
Carefully adjust the glass (A) until you can see the bolts, then loosen them. Separate the glass from the glass run and carefully pull the glass out through the window slot.
Tightening torque :
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)
Disconnect the power window motor connector (A).
Loosen the rear door power window regulatcr assembly mounting nuts.
Tightening torque :
3.9 ~ 5.9 N.m (0.4 ~ 0.6 kgf.m, 2.9 ~ 4.3 lb-ft)
Remove the rear door power window regulatcr assembly (A).
Installation is the reverse of removal.
Grease should be applied to areas where there is rotational parts and springs.
Roll the glass up and down to see if it move freely without binding.
Replace any damaged clips.
Remove the rear door trim.
Disconnect the speaker connector (B).
After loosening the mounting screws, then remove the speaker (A).
After loosening the mounting screws, then remove the rear door pull handle mounting support (B).
Remove the rear door trim seal (A).
Replace ant damaged door trim seal.
Disconnect the outside handle rod (A).
Loosen the rear door latch mounting screws.
Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Disconnect the rear door latch connector (A).
Remove the rear door latch (A).
Installation is the reverse of removal.
Make sure the door locks/unlocks and opens/closes properly.
Make sure the connector is connected properly.
Replace any damage clips.
Remove the following parts :
Rear door trim
Rear door seal
Disconnect the outside handle rod (A).
Remove the hole plug (B).
After loosening the mounting bolt, then remove the outside handle cover (A).
Tightening torque :
0.7 ~ 0.5 N.m (0.07 ~ 0.1 kgf.m, 1.0 ~ 0.7 lb-ft)
Remove the outside handle (A) by sliding it rearward.
Installation is the reverse of removal.
Make sure the door locks/unlocks and opens/closes properly.
Make sure the door locks and opens properly.
Loosen the checker mounting bolts.
Detach the clips, then remove the front door side weatherstrip (A).
Installation is the reverse of removal.
