1.
Remove the rear seat cushion (A).
Remove the rear seat cushion (A).
Disconnect the rear seat heater connectors (A).
After loosening the mounting bolts, then remove the rear seat back (A).
Tightening torque :
16.7 ~ 25.5N.m (1.7 ~ 2.6kgf.m, 12.3~18.8lb-ft)
Installation is the reverse of removal.
Make sure the connector is plugged in properly.
After loosening the mounting bolts and then remove the rear seat cushion assembly (A) by pulling it up.
Tightening torque :
16.7 ~ 25.5 N.m (1.7 ~ 2.6 kgf.m, 12.3 ~18.8 lb-ft)
Disconnect the rear seat heater connector (A).
Fold the rear seat back by pulling the rear seat folding lever (A) in the trunk.
After loosening the mounting bolts, then remove the rear seat back assembly (A).
Tightening torque :
16.7 ~ 25.5 N.m (1.7 ~ 2.6 kgf.m, 12.3 ~18.8 lb-ft)
Installation is the reverse of removal.
Make sure the connector is plugged in properly.
Remove the rear seat cushion assembly.
After loosening the mounting bolt and then remove the rear seat side back assembly (A) by pulling it up.
Tightening torque :
16.7 ~ 25.5 N.m (1.7 ~ 2.6 kgf.m, 12.3 ~18.8 lb-ft)
Installation is the reverse of removal.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage..
Put on gloves to protect your hands.
Remove the rear seat assembly.
After loosening the mounting nuts, then remove the rear back armrest (A).
After loosening the mounting screws, then remove the rear back armrest board (A),
Push the lock pin (B), remove the headrest (A).
Pull out the headrest guides (A) while pinching the end of the guides, and remove them.
Remove the hog-ring clips (A).
Disconnect the hog-ring clips (B) on the rear of seat back, remove the seat back cover (A).
Installation is the reverse of removal.
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
Replace the hog-ring clips with new ones using special tool [C (09880-4F000)].
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Remove the rear seat back assembly [LH].
Push the lock pin (B), remove the rear seat headrest (A).
Remove the rear seat side bracket cover (A) by using a screwdriver or remover.
Pull out the hooks (A) by the rear seat back frame.
Turn the rear seat back cover inside out. Then pull out the headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.
Remove the rear seat back cover (A) from the rear seat back frame (B).
After removing the hog-ring clips (A) on the rear of seat back and remove the rear seat back cover (B).
Installation is the reverse of removal.
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Remove the rear seat back assembly [RH].
Push the lock pin (B), remove the rear seat headrest (A).
Remove the rear seat side bracket cover (A) by using a screwdriver or remover.
Remove the rear seat armrest cover (A) and then loosen the mounting nuts.
Pull out the rear seat armrest (A).
Pull out the hooks (A) by the rear seat back frame.
Turn the rear seat back cover inside out. Then pull out the headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.
Remove the rear seat back cover (A) from the rear seat back frame (B).
After removing the hog-ring clips (A) on the rear of seat back and remove the rear seat back cover (B).
Installation is the reverse of removal.
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage..
Put on gloves to protect your hands.
Remove the rear seat cushion.
Disconnect the rear seat heater control unit connector (A).
Remove the hog-ring clips (A).
Disconnect the hog-ring clips (B) on the rear of seat cushion, remove the seat cushion cover (A).
Installation is the reverse of removal.
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
Replace the hog-ring clips with new ones using special tool [C (09880-4F000)].
Remove the rear seat back assembly.
Loosen the rear back armrest mounting nuts.
Remove the rear back armrest (A).
Installation is the reverse of removal.
Fold the rear seat back assembly.
Remove the rear seat armrest cover (A) and then loosen the mounting nuts.
Pull out the rear seat armrest (A).
Remove the cap (A) and remove the rear seat armrest (B) by loosening the mounting bolts.
Installation is the reverse of removal.
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Remove the package tray trim.
(Refer to the BD group - "Interior Trim")
Press the lock pin (A) located in the trunk and remove the rear seat back folding cable handle (B) by pushing it back.
After loosening the mounting bolts, then remove the rear seat latch assembly (A).
Tightening torque :
19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)
Pull out the rear seat latch cable (A).
Installation is the reverse of removal.
