Inspection
1.

Check the audio remote control switch (A) for resistance between connector terminals in each switch position.

[Audio/ Bluetooth/ Drive mode]
[Trip + Cruise]
[Voice recognition]
[ECO/ Trip/ Drive mode]
[Audio/ Bluetooth/ Drive mode]

Switch

Connector terminal

Resistance (±5%)

Seek up

2-7

430Ω

Seek down

2-7

1.11kΩ

Mode

2-7

2.11kΩ

Mute

2-7

3.11kΩ

Volume up

2-7

4.61kΩ

Volume down

2-7

6.81kΩ

Call off

2-7

18.91kΩ

Call on

2-7

40.91kΩ

Drive mode

4-6

4.1kΩ

[Trip]

Switch

Connector terminal

Resistance (±5%)

Trip

3-7

330Ω

Trip up

3-7

550Ω

Trip down

3-7

880Ω

Select

3-7

1.44kΩ

[Voice recogniton]

Switch

Connector terminal

Resistance (±5%)

Voice

Audio terminal 2 & Voice recognition 3

10.71kΩ

caution

When checking voice recognition switch resistance, audio control swtich and voice recognition switch should be connected.

[ECO/ Trip/ Drive mode]

Switch

Connector terminal

Resistance

(±5%)

Trip

2-4

330Ω

Trip up

2-4

550Ω

Trip down

2-4

880Ω

Select

2-4

1.44kΩ

ECO

2-4

2.54kΩ

Drive mode

2-4

5.54kΩ

Removal
[Upper Steering Wheel Remote Control Switch]
1.

Disconnect the negative (-) battery terminal.

2.

Remove the driver airbag module.

(Refer to the RT group)

3.

Remove the steering wheel.

(Refer to the ST group - "Steering column & shaft")

4.

Loosen the mounting screws from the rear steering wheel cover.

5.

Separate the upper left steering wheel remote control switch (A) after loosening the mounting screw.

6.

Remove the upper left steering wheel remote control switch (A) after disconnecting the connector.

[Lower Steering Wheel Remote Control Switch]
1.

Disconnect the negative (-) battery terminal.

2.

Remove the driver airbag module.

(Refer to the RT group)

3.

Remove the steering wheel.

(Refer to the ST group - "Steering column & shaft")

4.

Loosen the mounting screws from the front steering wheel cover.

5.

Remover the upper left steering wheel cover (A) after loosening the mounting screws.

6.

Separate the upper steering wheel remote control switch (A) after loosening the mounting screw.

[LH]
[RH]
7.

Remove the upper steering wheel remote control switch (A) after disconnecting the connector.

[LH]
[RH]
8.

Remove the steering wheel cover (A) after loosening the mounting screws from the front steering wheel cover.

9.

Remove the front steering wheel cover (B) after disconnecting the connector (A).

10.

Remove the lower steering wheel remote control switch (B) after disconnecting the connector (A).

[LH]
[RH]
Installation
[Upper Steering Wheel Remote Control Switch]
1.

Install the upper left steering wheel remote control switch and rear steering wheel cover.

2.

Install the steering wheel.

3.

Reconnect the remote control switch connector and airbag connectors.

note

Make sure that the switch connector is plugged in properly.

4.

Install the driver airbag module.

5.

Connect the negative (-) battery terminal.

[Lower Steering Wheel Remote Control Switch]
1.

Install the lower/ upper steering wheel remote control switch and front/ rear steering wheel cover.

2.

Install the steering wheel.

3.

Reconnect the remote control switch connector and airbag connectors.

note

Make sure that the switch connector is plugged in properly.

4.

Install the driver airbag module.

5.

Connect the negative (-) battery terminal.

Яндекс.Метрика