1.
Fold the second row seat assembly [RH] (A).
Fold the second row seat assembly [RH] (A).
Pull up the second row seat assembly [RH] (A) as far as possible.
Loosen the second center seat belt buckle mounting bolt (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)
Remove the seat track cover, then loosen the mounting bolts.
Tightening torque :
44.1~ 58.8 N.m (4.5 ~ 6.0 Kgf.m, 32.5~ 43.4 lb-ft)
Loosen the mounting bolt and seat belt buckle mounting bolt, then remove the seat assembly (A).
Disconnect the connector (A), then remove the seat assembly.
Install in the reverse order of removal.
Seat mounting bolt and nut installation procedure.
Tighten temporarily in the order of nut and bolt on the front of recliner hinge installation part.
After completely tightening completely the bolt on the back of the recliner hinge installaion part, tighten the bolt on the front of it completely.
Setting down the seat cushion, tighten the mounting bolt of the cushion frame hinge.
Check if reclining the seat and folding seat back operate smoothly.
Push the lock pin (B), and then remove the headrest (A).
When prying with a flat-up screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
After loosening the mounting bolt, then remove the armrest (A).
Push the hook (A), remove the headrest guide (B).
Using a screwdriver or remover, remove the armrest cover (A).
Loosen the cover mounting screws (A).
Remove the cover (A) by using a flat-tip screwdriver.
Using a screwdriver or remover, remove the cover (A).
When prying with a flat-up screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Remove the seat back panel (A).
Remove the cap.
Loosen the screw and then recliner cover (A).
Using a screwdriver or remover, remove the rear center seat belt upper anchor cover (A).
Disconnect the protector
Remove the headrest guide (A).
After removing the hogring clips (B) on the front of seat cushion and remove the seat cushion cover (A).
Installation is the reverse of removal.
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hogring clips (A).
Replace the hogring clips with new ones using special tool (C).
Remove the seat cushion.
Loosen the recliner lever mounting screw and then disconnect the lever (A).
Disconnect the recliner cable (A).
After loosen the mounting bolts, then remove the seat back frame (A).
Install in the reverse order of removal.
Remove the seat back cushion cover.
After loosening the mounting bolt, then remove the back folding hinge cover (A).
After loosening the mounting bolt, then remove the bracket (A).
After loosening the mounting screw, then remove the recliner cover (A).
When prying with a flat-up screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Disconnect the heated seat connector (A) mounting clip.
Disconnect the protector (B), and then remove the seat cushion (A).
After removing the hogring clips (B) on the front of seat cushion and remove the seat cushion cover (A).
Install in the reverse order of removal.
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hogring clips (A).
Replace the hogring clips with new ones using special tool (C).
Remove the seat back cover.
Remove the recliner cover.
Loosen the seat cushion mounting bolt (A).
Remove the seat mounting cover (A).
Loosen the mounting screw and then remove the recliner cover (A).
Remove the seat mounting cover (A).
After loosening the mounting screw, then remove the recliner cover (A).
After loosening the mounting bolt, then remove the seat cushion frame (A).
Install in the reverse order of removal.
Fold the second row seat assembly [RH] (A).
Pull up the second row seat assembly [RH] (A) as far as possible.
Disconnect the seat heater connector (A).
Loosen the seat mounting nuts.
Tightening torque :
39.2~ 53.9 N.m (4.0 ~ 5.5 Kgf.m, 28.9 ~ 39.8 lb-ft)
After loosening the mounting bolts, then remove the seat assembly (A).
Tightening torque :
44.1 ~ 58.8 N.m (4.5 ~ 6.0 Kgf.m, 32.5 ~ 43.4 lb-ft)
Install in the reverse order of removal.
Disconnect the mounting clips (B), and then disconnect the cover (A).
After loosening the mounting screw, then remove the recliner cover (A).
When prying with a flat-up screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Remove the cover (A).
Loosen the seat cushion mounting bolt (A).
After loosening the mounting nuts, then remove the seat cushion (A).
Disconnect the seat heater wirering mounting clip (A).
Disconnect the protector (A), and then remove the seat cushion.
After removing the hogring clips (B) on the front of seat cushion and remove the seat cushion cover (A).
Install in the reverse order of removal.
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hogring clips (A).
Replace the hogring clips with new ones using special tool (C).
Disconnect the recliner cable (A).
Remove the cap.
After loosening the mounting screw, then remove the recliner cover (A).
Using a screwdriver or remover, remove the cover (A).
Remove the seat back panel (A).
Disconnect the protector (A).
Push the lock pin, remove the headrest (A).
Remove the headrest guide (A).
After removing the hogring clips (B) on the front of seat cushion and remove the seat cushion cover (A).
Install in the reverse order of removal.
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hogring clips (A).
Replace the hogring clips with new ones using special tool (C).
Remove the seat back cover.
After loosening the mounting screws, then disconnect the lever (A).
Disconnect the recliner cable (A).
Loosen the mounting bolts and then remove the seat back frame (B).
Install in the reverse order of removal.
Remove the luggage box trim (A).
Remove the luggage box partition trim (A).
Loosen the mount bolts.
Tightening torque :
44.1~58.8N.m (4.5 ~ 6.0Kgf.m, 32.5~43.4lb-ft)
Remove the cap.
After loosening the mounting bolts, then remove the third seat assembly (A).
Tightening torque :
44.1~ 58.8N.m (4.5 ~ 6.0Kgf.m, 32.5~43.4lb-ft)
Install in the reverse order of removal.
Loosen the bolt.
Loosen the bolt and then remove the seat cushion (A).
Disconnect the protector (A).
Disconnect the protector (A) and then remove the seat cushion cover.
After removing the hogring clips (B) on the front of seat cushion and remove the seat cushion cover (A).
Install in the reverse order of removal.
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hogring clips (A).
Replace the hogring clips with new ones using special tool (C).
Using the screw driver, remove the cover (A).
Zip off the seat back cover (A), and then pull it up.
After loosening the mounting screws, then remove the panel (A).
Disconnect the protector (A).
Push the hook, remove the headrest guide (A).
After removing the hogring clips (B) on the front of seat cushion and remove the seat cushion cover (A).
Install in the reverse order of removal.
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hogring clips (A).
Replace the hogring clips with new ones using special tool (C).
Remove the seat cushion.
Remove the seat back.
After loosening the mounting screw, then remove the cover (A).
Disconnect the cable (A).
After loosening the recliner mounting bolts, then remove the seat back frame (B).
Install in the reverse order of removal.
