2.
Push the lock pin (B), disconnect the tweeter speaker connector (C).
When prying with a flat-tipped screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the quadrant inner cover (A).
Push the lock pin (B), disconnect the tweeter speaker connector (C).
Using a screwdriver (B), remove the door grip handle cover (A).
Using a screwdriver, remove the door inside handle cap (B).
After loosening the mounting screws, then remove the door trim (A).
Push the hook (B), remove the inside handle cage (A)
Push the lock pin (A), disconnect the connectors (B).
Push the lock pin, disconnect the connectors (B).
Remove the door trim.
Install in the reverse order of removal.
Make sure of connectors is plugged in properly and each rod is connected securely.
Make sure the door lock and opens properly.
Replace ant damaged clips.
Remove the door trim.
After loosening the mounting screws, then remove the inside handle (A).
Install in the reverse order of removal.
Make sure the door lock and opens properly.
Replace ant damaged clips.
Remove the front door trim.
Remove the glass mounting plug hole.
Take care not to drop to glass and scratch the glass surface.
Carefully adjust the glass (B) until you can see the bolts, then loosen them. Separate the glass from the glass run and carefully pull the glass out through the window slot.
Tightening torque :
8.8~11.8 N.m (0.9~1.2 kgf.m, 6.5~8.7 lb-ft)
Install in the reverse order of removal.
Roll the glass up and down to see if it move freely without binding.
Adjust glass position as needed.
Replace ant damaged clips.
Make sure the door lock and opens properly.
Remove the door trim.
Drill out the rivets to remove the speaker (B) from the door module.
Disconnect the speaker connector (A).
Install in the reverse order of removal.
Use sheet metal screws to secure the speaker.
Replace ant damaged clips.
Make sure the door lock and opens properly.
Make sure the connector are connected properly and each rod is connected securely.
Remove the door trim.
Disconnect the connector (A), then loosen the mounting screws.
Remove the power window motor (B).
Install in the reverse order of removal.
Grease should be applied to areas where there is rotational parts and springs.
Roll the glass up and down to see if it move freely without binding.
Replace ant damaged clips.
Make sure the door lock and opens properly.
Remove the following parts :
Front door trim
Window glass
Outside handle
Loosen the outside handle base mounting screw (A).
Loosen the module mounting bolts.
After loosening the lach mounting screws, remove the module (A).
Tightening torque :
6.9~10.8 N.m (0.7~1.1 kgf.m, 5.1~8.0 lb-ft)
Push the lock pin (B), disconnect the connector (A).
Disconnect the clip (C).
Pull out the lock pin (A), disconnect the main connector (B).
Install in the reverse order of removal.
The area of whole parts should be applied with sufficient grease.
Make sure connected are connected properly and each rod is connected securely.
Make sure the door lock and opens properly.
Replace ant damaged clips.
Remove the cap, loosen the mounting bolt.
Remove the outside handle cover (A).
Tightening torque :
7.8~11.8 N.m (0.8 ~1.2 kgf.m, 5.8~8.7 lb-ft)
Remove the outside handle (A)
Installation is the reverse the removal.
Make sure door lock operates and door open/closes properly.
Check the glass run channel for damage or deterioration, and replace them necessary.
Remove the door trim.
Carefully move the glass (A) until the glass mounting bolt are visible, then loosen them.
Check that the glass moves smoothly.
Make sure the door latches securely without slamming it. If necessary adjust the striker (A): The striker nuts are fixed. The striker can be fine adjusted up or down, and in or out.
Loosen the screws (B), then insert a shop towel between the body and striker.
Tightening torque :
B : 16.7~21.6 N.m (1.7 ~2.2 kgf.m, 12.3~15.9 lb-ft)
Lightly tighten the screws.
Wrap the striker with a shop towel, then adjust the striker by tapping it with a plastic hammer. Do not tap the striker too hard.
Loosen the screws and remove the shop towel.
Lightly tighten the screws.
Hold the outer handle out, and push the door against the body to be sure the striker allows a flush fit. If the door latches properly, tighten the screws and recheck.
After installing the door, check for a flush fit with the body, then check for equal gaps between the front, rear, and bottom, door edges and the body. Check that the door and body edges are parallel. Before adjusting, replace the mounting bolts.
Check that the door and body edges are parallel.
Place the vehicle on a firm, level surface when adjusting the doors.
Adjust at the hinges (A):
Loosen the door mounting bolts slightly, and move the door IN or OUT until it aligns flush with the body.
Loosen the hinge mounting bolts slightly, and move the door backward or forward, up or down as necessary to equalize the gaps.
Place a shop towel on the jack to prevent damage to the door when adjusting the door.
Tightening torque :
B : 21.6~26.5 N.m (2.2 ~2.7 kgf.m, 15.9~19.5 lb-ft)
C : 33.3~41.2 N.m (3.4~4.2 kgf.m, 24.6~30.4 lb-ft)
Check that the door and body edges are parallel.
Grease the pivot portions of the hinges indicated by the arrows.
Check for water leaks.
