4.
Disconnect the inhibitor switch connect (A) and solenoid valve connector (B).
Remove the engine cover.
(Refer to Engine Mechanical System - "Engine cover")
Remove the air cleaner assembly and air duct.
(Refer to Engine Mechanical System - "Air cleaner")
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
Disconnect the inhibitor switch connect (A) and solenoid valve connector (B).
Remove the shift cable (B) after removing the nut (C) and the bolt (A).
Tightening torque :
(A) 14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)
(C) 7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)
Remove the ground line after removing the bolt (A).
Tightening torque :
(A) 10.8 ~ 13.7 N.m (1.1 ~ 1.4 kgf.m, 8.1 ~ 10.1 lb-ft)
Disconnect the pad (A).
Assembled the engine support fixture (A).
(Refer to Special Service Tools - " Engine support fixture special tool assembly drawing")
Disconnect the coolant hose (B) after removing the automatic transaxle coolant hose clamp (A).
Remove the wiring mounting clip (C).
Remove the coolant pipe mounting bolts (A).
Remove the coolant pipe (B).
Tightening torque :
(A) 8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)
Remove the wiring bracket installation bolt (A).
Remove the hood lift.
(Refer to Body - "Hood")
Using the engine support fixture (A) , hold the engine and transaxle assembly safely.
Remove the automatic transaxle upper mounting bolt (A-2ea) and the starter motor mounting bolt (B-2ea).
Tightening torque :
(A), (B) 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
Remove the mounting bracket cover (A).
Remove the automatic transaxle mounting bracket bolt (A).
Tightening torque :
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)
Remove the automatic transaxle mounting support bracket bolts (A).
Remove the automatic transaxle mounting support bracket (B).
Tightening torque :
58.8 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)
Remove the under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
Remove the side cover (A).
Tightening torque :
7.8 ~ 11.8 N.m (0.8 ~ 1.2kgf.m, 5.8 ~ 8.7 lb-ft)
Remove the following items;
2WD
Sub frame assembly.
(Refer to Suspension System - "Sub Frame")
Drive shaft assembly.
(Refer to Driveshaft and axle - "Drive shaft assembly")
4WD
Sub frame assembly.
(Refer to Suspension System - "Sub Frame")
Drive shaft assembly.
(Refer to Driveshaft and axle - "Drive shaft assembly")
Transfer assembly.
(Refer to Transfer system - "Transfer assembly")
Remove the dust cover (A).
Remove the torque converter mounting bolt (A) with rotating the crankshaft.
Tightening torque :
45.1 ~ 52.0 N.m (4.6 ~ 5.3 kgf.m, 33.3 ~ 38.3 lb-ft)
Remove the automatic transaxle with a jack after removing the mounting bolt (A-4ea, B-2ea).
Tightening torque :
(A) 42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)
(B) 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
