3.
Remove the ground line after removing the bolt (A).
Air cleaner assembly and air duct.
(Refer to Engine Mechanical System - "Air cleaner")
Battery and battery tray.
(Refer to Engine Electrical System - "Battery")
Remove the ground line after removing the bolt (A).
Remove the wiring mounting bolt (A).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
Remove the wiring clip from the bracket.
Dissconnect the solenoid valve connector (A) and inhibitor switch connector (B).
Remove the shift cable (C) after removing the nut (A) and the bolt (B).
Tightening torque:
(A) 9.8 ~ 13.7 N.m (1.0 ~ 1.4 kgf.m, 7.2 ~ 10.1 lb-ft)
(B) 14.7 ~ 21.6 N.m(1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)
Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).
Remove the automatic transaxle upper mounting bolt (A-2ea) and the starter mounting bolt (B-2ea).
Tightening torque :
(A) 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
(B) 49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)
Remove the cowl top cover.
(Refer to Body - "Cowl Top Cover")
Assemble the engine support fixture.
(Refer to Special Service Tools-"Engine support fixture assembly drawing")
Using the engine support fixture (beam No.: 09200-38001 or 09200-3N000, supporter No.: 09200-2S000, adapter No.: 09200-4X000), hold the engine and transaxle assembly safely.
Remove the cover (A).
Remove the automatic transaxle mounting bracket bolts (A).
Tightening torque:
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.8 lb-ft)
Remove the automatic transaxle support bracket (A).
Tightening torque:
58.8 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)
Lift the vehicle with a jack.
Remove the under cover (A).
Remove the bracket (A).
Remove the drive shaft assembly.
(Refer to Driveshaft and axle - "Front Driveshaft")
Remove the sub frame.
(Refer to Suspension System - "sub frame")
Remove the dust cover (A).
Tightening torque:
42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)
Remove the torque converter mounting bolt (A) with rotating the crankshaft.
Tightening torque:
45.1 ~ 52.0 N.m (4.6 ~ 5.3 kgf.m, 33.3 ~ 38.3 lb-ft)
Lubricant should be applied on thread of bolt before tightening.
Remove the drive shaft cover (A).
Remove the mounting bolt (A, B) after supporting the transaxle by a jack.
Tightening torque
(A) 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
(B) 42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)
Remove the transaxle while slowly lower the jack.
Be careful not to damage other system or parts near by when removing the transaxle assembly.
