3.
Remove the ground line after removing the bolt (A).
Air cleaner assembly and air duct.
(Refer to Engine Mechanical System - "Air cleaner")
Battery and battery tray.
(Refer to Engine Electrical System - "Battery")
Remove the ground line after removing the bolt (A).
Remove the wiring mounting bolt (A).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
Remove the wiring clip from the bracket.
Dissconnect the solenoid valve connector (A) and inhibitor switch connector (B).
Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).
Remove the shift cable (C) after removing the nut (A) and the bolt (B).
Tightening torque:
(A) 9.8 ~ 13.7 N.m (1.0 ~ 1.4 kgf.m, 7.2 ~ 10.1 lb-ft)
(B) 14.7 ~ 21.6 N.m(1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)
Remove the under cover (A).
Loosen the intercooler pipe bolts (A).
Tightening torque:
19.6 ~ 26.5 N.m (2.0 ~ 2.7 kgf.m, 14.5 ~ 19.5 lb-ft)
Remove the brake vacuum pump.
(Refer to Brake System - "Brake Booster")
Remove the automatic transaxle upper mounting bolt (A-2ea) and the starter mounting bolt (B-2ea).
Tightening torque :
(A) 42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
(B) 49.0 ~ 63.7N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)
Remove the cowl top cover.
(Refer to Body - "Cowl Top Cover")
Assemble the engine support fixture.
(Refer to Special Service Tools-"Engine support fixture assembly drawing")
Using the engine support fixture (beam No.: 09200-3N000, supporter No.: 09200-2S000, adapter No.: 09200-4X000), hold the engine and transaxle assembly safely.
Remove the cover (A).
Loosen the transaxle mounting bracket bolts (A).
Tightening torque:
98.1 ~ 117.7 N.m (10.0 ~ 12.0 kgf.m, 72.3 ~ 86.8 lb-ft)
Remove the transaxle support bracket (A).
Tightening torque:
58.8 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)
Remove the drive shaft assembly.
(Refer to Driveshaft and Axle - "Front Driveshaft")
Remove the dust cover (A).
Remove the torque converter mounting bolts (A) with rotating the crankshaft.
Tightening torque:
45.1 ~ 52.0 N.m (4.6 ~ 5.3 kgf.m, 33.3 ~ 38.3 lb-ft)
Remove the roll rod bracket (C) after removing bolt (A,B).
Tightening torque:
(A) 49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)
(B) 107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94.0 lb-ft)
Remove the mounting bolt (A, B) after supporting the transaxle by a jack.
Tightening torque:
(A) 42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
(B) 42.2 ~ 48.1 N.m (4.9 ~ 5.5 kgf.m, 31.1 ~ 35.4 lb-ft)
Remove the transaxle while slowly lower the jack.
Be careful not to damage other system or parts near by when removing the transaxle assembly.
