2.
Disconnect the vehicle speed sensor connector (A) and back up lamp switch connector (B).
Remove the following items.
Air cleaner assembly
(Refer to Engine Mechanical System - "Air Cleaner")
Battery and battery tray
(Refer to Engine Electrical System -"Battery")
Disconnect the vehicle speed sensor connector (A) and back up lamp switch connector (B).
Remove the wiring bracket (A).
Remove the ground (A).
Remove the control cable.
Remove the pin (A) and washer (B).
Remove the bracket mounting bolts (C).
Remove the pin (A) and then Remove the concentric slave cylinder tube (B).
Remove the cowl top cover.
(Refer to Body - "Cowl Top Cover")
Using the engine support fixture (Support SST No.: 09200-2S100/2S200, Adapter SST No.: 09200-4X000, Beam SST No.: 09200-3N000 or 38001), hold the engine and transaxle assembly safely.
Remove the transaxle upper mounting bolt (B-2ea) and the start motor mounting bolt (A-2ea).
Tightening torque:
(A) 49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)
(B) 42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
Remove the cover (A).
Remove the transaxle mounting bracket bolts (A) and then loosen the transaxle support bracket bolts (B).
Tightening torque:
(A) 88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)
(B) 58.9 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.8 lb-ft)
Remove the under cover.
Remove the Intercooler pipe mounting bolts (A) and clamp (B).
Remove the vacuum pump.
(Refer to Brake System - "Brake Booster")
Remove the drive shaft assembly.
(Refer to Driveshaft and axle - "Front Driveshaft")
Remove the drive shaft cover (A).
Remove the roll rod bracket (C) after removing bolt (A,B).
Tightening torque:
(A) 49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)
(B) 107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94.1 lb-ft)
Remove the mounting bolts (A-3ea, B-2ea) of lower part of the transaxle, and remove the transaxle assembly by supporting it with a jack.
Tightening torque:
(A) 42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)
(B) 42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)
Be careful not to damage other system or parts near by when removing the engine and transaxle assembly.
If the oil seal on the transaxle case side is damaged and fluid is leaking, replace the oil seal with a new unit. When installing the new oil seal, use the specialized tool (oil seal installer, 09453-2F300).
Install in the reverse order of removal.
Adding manual transaxle fluid after Installing the manual transaxle.
(Refer to Manual Transaxle System - "Manual Transaxle Fluid")
Perform bleeding air procedure in concentric slave cylinder after pouring the brake fluid.
(Refer to Concentric Slave Cylinder Assembly - "Adjustment")
