1.
Install the transaxle lower mounting bolts (A-3ea,B-1ea) after fitting the transaxle assembly into the engine assembly.
Tightening torque :
[A] 34.3~49.1 N.m (3.5~5.0 kgf.m, 25.3~36.2 lb-ft)
[B] 42.2~54.0 N.m (4.3~5.5 kgf.m, 31.1~39.8 lb-ft)
Install the transaxle lower mounting bolts (A-3ea,B-1ea) after fitting the transaxle assembly into the engine assembly.
Tightening torque :
[A] 34.3~49.1 N.m (3.5~5.0 kgf.m, 25.3~36.2 lb-ft)
[B] 42.2~54.0 N.m (4.3~5.5 kgf.m, 31.1~39.8 lb-ft)
Install the bolt left in the engine side.
Tightening torque :
42.2~54.0 N.m (4.3~5.5 kgf.m, 31.1~39.8 lb-ft)
Install the clutch release cylinder assembly(A) by installing bolts(B-2ea).
Tightening torque :
14.7~21.6 N.m (1.5~2.2 kgf.m, 10.8~15.9 lb-ft)
Install the roll stopper bracket by installing bolts(A-1ea,B-2ea).
Tightening torque :
[A] 107.9~127.5 N.m (11.0~13.0 kgf.m, 79.6~94.1 lb-ft)
[B] 49.1~63.8 N.m (5.0~6.5 kgf.m, 36.2~47.0 lb-ft)
Tighten the turbo charger hose by tightening a clamp and installing the bolts(2ea).
Install the dust cover by installing the bolts(2ea).
Connect the drive shafts to the transaxle. (Refer to "Front Driveshaft" in DS group)
Refill the transaxle fluid through the filler hole. (Refer to Service Adjustment Procedure)
Install the under cover (A).
Install the transaxle support bracket bolts (A-3ea).
Tightening torque :
88.3~107.9 N.m (9.0~11.0 kgf.m, 65.1~79.6 lb-ft)
Install the transaxle upper mounting bolts (A-2ea) the starter motor mounting bolts (B-2ea).
Tightening torque :
[A] 58.9~78.5 N.m (6.0~8.0 kgf.m, 43.4~57.9 lb-ft)
[B] 38.3~58.9 N.m (3.9~6.0 kgf.m, 28.2~43.4 lb-ft)
Remove the engine support fixture [Support (A)-SST No.: 09200-1P000, Beam (B)-SST No.: 09200-38001] from the vehicle.
Install the head lamp.(Refer to "Lighting System" in BE group.)
Install the cowl complete assembly panel (A).
Install the cowl top cover or wiper motor. (Refer to "Windshield Wiper/Washer" in BE group.)
After installing the bracket mounting bolt (B), install the clutch tube with the clip (A).
Tightening torque :
14.7~21.6 N.m (1.5~2.2 kgf.m, 10.8~15.9 lb-ft)
Install the CKP sensor by installing a bolt.
Tightening torque :
6.9~10.8 N.m (0.7~1.1 kgf.m, 5.1~8.0 lb-ft)
Install the control cable bracket by installing bolts(3ea).
Tightening torque :
14.7~21.6 N.m (1.5~2.2 kgf.m, 10.8~15.9 lb-ft)
Install the clips (B) and pins (A).
Connect the neutral switch connector.
Install the ground wire by installing a bolt.
Connect the vehicle speed sensor connector (A) and the back lamp switch connector (B).
Install the battery tray (A).
Install the ECU and battery. (Refer to "Charging System" in EE group)
Install the engine cover and air cleaner assembly. (Refer to "Intake and exhaust system" in EM group)
