1.
Using a screwdriver or remover, remove the quadrant inner cover (A).
Take care not to scratch the door trim and other parts.
Put on gloves to protect your hands.
Using a screwdriver or remover, remove the quadrant inner cover (A).
After loosening the mounting screws, then remove the door trim (A).
Remove the inside handle cable (A).
Push the lock pin, disconnect the connectors (A).
Installation is the reverse of removal.
Make sure of connectors is plugged in properly and each rod is connected securely.
Make sure the door lock and opens properly.
Remove the door trim.
After loosening the door inside handle mounting screws, then remove the door inside handle (A).
Installation is the reverse of removal.
Remove the front door trim.
Remove the door belt inner weatherstrip (A).
Remove the glass mounting hole plug.
Take care not to drop to glass and scratch the glass surface.
Carefully move the glass (A) until you can see thebolts, then loosen them. Separate the glass from theglass run and carefully pull the glass out through thewindow slot.
Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Installation is the reverse of removal.
Roll the glass up down to see if it move freely without binding.
Adjust the position of the glass as necessary.
Remove the door trim.
Drill out the rivets to remove the speaker (B) from the door module.
Disconnect the speaker connector (A).
Installation is the reverse of removal.
Use sheet metal screws to secure the speaker.
Make sure the connector are connected properly and each rod is connected securely.
Make sure the door lock and opens properly.
Remove the door trim.
After loosening the mounting screws, then remove the power window motor (A).
Disconnect the connector (B).
Installation is the reverse of removal.
The area of rotational parts and springs should be applied with sufficient grease.
Roll the glass up down to see if it move freely without binding.
Remove the following parts.
Door trim.
Window glass
Outside handle.
Loosen the mounting screw (A).
Loosen the door module mounting bolts, and then remove the door module (A).
Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Disconnect the connector (A).
Disconnect the door module wiring harness (B), and then remove the module assembly.
Installation is the reverse of removal.
The area of whole parts should be applied with sufficient grease.
Make sure the connector is plugged in properly and each rod is connected securely.
Make sure the door lock and open properly.
Remove the hole plug (B).
After loosening the mounting bolt, then remove the outside handle cover (A).
Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Remove the outside handle (A) by sliding it rearward.
Remove the outside handle pad (A).
Installation is the reverse the removal.
Make sure the door lock and open properly.
Loosen the checker mounting bolts.
Detach the clips, then remove the door side weatherstrip(A).
Installation is the reverse of removal.
Check the glass run channel for damage or deterioration, and replace them necessary.
Remove the door trim.
Carefully move the glass (A) until you can see theglass mounting bolts, then loosen them.
Check that the glass moves smoothly.
Make sure the door latches securely without slamming it. If necessary adjust the striker (A): The striker nuts are fixed. The striker can be fine adjusted up or down, and in or out.
Loosen the screws (B), then insert a shop towel between the body and striker.
Tightening torque :
(B): 16.7 ~ 21.6 N.m (1.7 ~ 2.2 kgf.m, 12.3 ~ 15.9 lb-ft)
Lightly tighten the screws.
Wrap the striker with a shop towel, then adjust the striker by tapping it with a plastic hammer.
Do not tap the striker too hard.
Loosen the screws and remove the shop towel.
Lightly tighten the screws.
Hold the outer handle out, and push the door against the body to be sure the striker allows a flush fit. If the door latches properly, tighten the screws and recheck.
After installing the door, check for a flush fit with theBody, then check for equal gaps between the front,Rear, and bottom, door edges and the body. CheckThat the door and body edges are parallel. BeforeAdjusting, replace the mounting bolts.
Place the vehicle on a firm, level surface when adjusting the doors.
Check that the door and body edges are parallel.
Adjust at the hinges (A) :
Loosen the door mounting bolts slightly, and move the door IN or OUT until it aligns flush with the body.
Loosen the hinge mounting bolts slightly, and move the door backward or forward, up or down as necessary to equalize the gaps.
Place a shop towel on the jack to prevent damage to the door when adjusting the door.
(Special service tool : 09793-21000)
Tightening torque :
(B) : 33.4 ~ 41.2 N.m (3.4 ~ 4.2 kgf.m, 24.6 ~ 30.4 lb-ft)
(C) : 21.6 ~ 26.5 N.m (2.2 ~ 2.7 kgf.m, 15.9 ~ 19.5 lb-ft)
Grease the pivot portions of the hinges indicated.
Check for water leaks.
