1.
Remove the door delta inner cover (A).
Take care not to scratch the door trim and other parts.
Put on gloves to protect your hands.
Remove the door delta inner cover (A).
After loosening the mounting screws, then remove the door trim (A).
Disconnect the inside handle cable (A).
Disconnect the power window connector (B).
Installation is the reverse of removal.
Make sure connectors are connected properly and each rod is connected securely.
Make sure the door lock and opens properly.
Replace ant damaged clips.
Push the clip (C) using a piece of cloth (B), and then remove the door window regulator handle (A).
[ Manual type only]
Installation is the reverse of removal.
Remove the door trim.
After loosening the door inside handle mounting screws, then remove the door inside handle (A).
Installation is the reverse of removal.
Put on gloves to protect your hands.
Remove the door trim.
Remove the door belt inner weatherstrip (A).
After loosening the mounting screws, then remove the delta cover (A).
Loosen the rear channel (A), mounting bolt and nut.
Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Remove the glass mounting plug hole.
Using the door switch to align the mounting hole with the hole on the door glass.
If it is impossible, align the hole by hand after removing the motor.
Be careful not to drop to glass and scratch the glass surface.
Carefully adjust the glass (A) until you can see the bolts, then loosen them. Separate the glass from the glass run and carefully pull the glass out through the window slot.
Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Installation is the reverse the removal.
Roll the glass up down to see if it move freely without binding
Adjust the position of the glass as needed.
Make sure the door lock and opens properly.
Replace ant damaged clips
Remove the door trim.
Drill out the rivets to remove the speaker (A).
Disconnect the speaker connector (B).
Installation is the reverse of removal.
Use sheet metal screws to secure the speaker.
Remove the door trim.
Disconnecting the power window motor connector (B).
After loosening the mounting screws, then remove the power window motor (A).
Installation is the reverse of removal.
The area of rotational parts and springs should be applied with sufficient grease.
Roll the glass up down to see if it move freely without binding.
Remove the hole plug (B).
After loosening the mounting bolt, then remove the outside handle cover (A).
Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Remove the outside handle (A) by sliding it rearward.
Remove the outside handle pad (A).
Installation is the reverse of removal.
Make sure the door lock and open properly.
Remove the following parts.
Door trim
Window glass
Outside handle
Loosen the mounting screw (A).
Loosen the rear channel (A), mounting bolts and nut.
Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
After loosening the door module mounting bolts, then remove the door module (A).
Tightening torque :
6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)
Disconnect the connector (B).
Detach the clips, then remove the wiring harness(C).
Installation is the reverse of removal.
The area of whole parts should be applied with sufficient grease.
Make sure the connector is plugged in properlyand each rod is connected securely.
Make sure the door lock and open properly.
Loosen the checker mounting bolts.
Detach the clips, then remove the door side weatherstrip (A).
Installation is the reverse the removal.
